The aqua v2 has Stainless steel and PolyCarbonate tanks with a third top so it can be used as a dripper.
The tanks hold 4 ml of ejuice.
The airflow is adjustable full lung hits to mouth to lung and every thing in between.
It has a two post design but post holes drilled in different directions so you can install two coils no problem. I hate dual coils. So I am trying it in single coil mode. This has four juice wells so if you want to rock this on a single coil you will have to plug two of the juice wells to keep it from flooding. I just packed the two wells. A reviewer on You Tube made a second wick and laid the uncoiled wick over the deck.
The bottom of the tank unscrews and you can remove the 510 pin and put another nut on and use in in hybrid mode and screw the tank directly into some mech mods.
Currently I have the tank sitting in a shot glass to catch any leaks. I will see how it goes and post an update.
I have several problems. With the aqua 2.
1. I had to close the airflow half way before the juice stopped leaking at the threads.
2. Most times I tried to unscrew the base from the tank I unscrewed the stupid bottom section to be used in hybrid mode.
3. No drip tip but used a standard 510 drip tip.
4. The PolyCarbonate tank is not clear but frosted. You can see the juice easily but if the juice starts to turn dark you will not be able to tell right away.
5. This fills from the bottom but there are four tiny holes that allow the juice to drip on the area around the juice wells. My problem is the holes you have to put the juice into the tank are tiny a dropper from a bottle is not going to work. I use 15 ml plastic bottles with a plastic needle tip and it barely worked.
You may want to think of filling with a syringe.
6. The threads are rough.
7. This kept leaking at the threads until I covered the airflow half way (a restrictive lung hit) my aqua v2 has leaked a fraction. Of a drop around the 510 pin ln 12 hours.
I took a couple of puffs and the tank has not flooded
Recommended yes but not for beginners.
The flavor is good but the Goblin Mini and Jim G's Kayfun Lite Plus with PolyCarbonate Bell cap has this setup beat but not by much
I got this because I am looking for options after I strip the threads or destroy the gaskets of my Goblin Mini.
The tanks hold 4 ml of ejuice.
The airflow is adjustable full lung hits to mouth to lung and every thing in between.
It has a two post design but post holes drilled in different directions so you can install two coils no problem. I hate dual coils. So I am trying it in single coil mode. This has four juice wells so if you want to rock this on a single coil you will have to plug two of the juice wells to keep it from flooding. I just packed the two wells. A reviewer on You Tube made a second wick and laid the uncoiled wick over the deck.
The bottom of the tank unscrews and you can remove the 510 pin and put another nut on and use in in hybrid mode and screw the tank directly into some mech mods.
Currently I have the tank sitting in a shot glass to catch any leaks. I will see how it goes and post an update.
I have several problems. With the aqua 2.
1. I had to close the airflow half way before the juice stopped leaking at the threads.
2. Most times I tried to unscrew the base from the tank I unscrewed the stupid bottom section to be used in hybrid mode.
3. No drip tip but used a standard 510 drip tip.
4. The PolyCarbonate tank is not clear but frosted. You can see the juice easily but if the juice starts to turn dark you will not be able to tell right away.
5. This fills from the bottom but there are four tiny holes that allow the juice to drip on the area around the juice wells. My problem is the holes you have to put the juice into the tank are tiny a dropper from a bottle is not going to work. I use 15 ml plastic bottles with a plastic needle tip and it barely worked.
You may want to think of filling with a syringe.
6. The threads are rough.
7. This kept leaking at the threads until I covered the airflow half way (a restrictive lung hit) my aqua v2 has leaked a fraction. Of a drop around the 510 pin ln 12 hours.
I took a couple of puffs and the tank has not flooded
Recommended yes but not for beginners.
The flavor is good but the Goblin Mini and Jim G's Kayfun Lite Plus with PolyCarbonate Bell cap has this setup beat but not by much
I got this because I am looking for options after I strip the threads or destroy the gaskets of my Goblin Mini.
