Boro Mod's, Tanks, Attys And More
- Thread starter badinfluence357
- Start date
- th_trl_thread_readers 19
I didn't check the stock of how many they had left earlier. But I just checked and they only have 7 left. Not knowing if these are going to be a one production run and done or not. I just grabbed another one just in case.
Probably hard to say with such a flooded boro market but hopefully they do more runs. More colours too.
Methinks it's this one. @Mark Todd did a recent review of it. Excellent job too, as is always the case.
Suicide Mods x Death Wish Rift AIO DNA60C Boro Mod
The Rift AIO. See DP's post above linking Todd's review. Also Jim VV' yt reviewed it.
Jim's review was good too - thanks for pointing that out, Pigs.
If I wasn't so disgustingly over-loaded with mods, I'd be tempted to buy one. I like the looks of them. Just a touch "Jazzy".
Yeah. I went overboard, for sure. I was trying to make room last week and ended up packing some stuff into a box, which will now sit out of sight in a semi-storage area of my house. Vape sacrilege!
My stepdaughter was here a week or so ago. She's been vaping almost as long as I have, and was picking up juice and coils. She looked around my "office" (and vape den) and I saw her wheels turning, and she was clearly stifling laughter. I said, "What, Jenn?"
Her reply was priceless. She said, "Exactly how many more years do you expect to live?"
Sooooooooo - I should probably stop buying mods ("We Are Vapers!").
What’s the main draw of boro modsYep, the SXK Ionbox is a definite keeper for certain! I finally got around to removing the boro from the previous pic above, and had a smile on my face after it dropped into my hand when released with absolutely NO condensation after 4 days of exclusive use....
View attachment 978576
Way back when, it was the only way to vape in a small compact mode. Much has changed since then though, but one constant is that they're still quite popular. A trip around here or Facebook will confirm that, leaving zero doubt.
Amazing, Billetbox never imagined the BB's would become the most popular aio around the world. Someone decided to customize it to work with an 18650 battery and Boom!! The rest is history....
It was actually him (the artist formerly known as Doug Dino) that brought the 18650s into play. The Rev4 switched from two 16340s to one 18650 + Evolv chips.
Not TOO long afterwards (maybe a year or so), the floodgates opened up. They haven't stopped flowing since.
No matter what atty I use the check Atty message pops up. The ohm's on the attys are in the .25 range, and the mod shows ohm's in the .50 range. Opened up found a little juice by the fire button but noting crazy. It wasn't on the switch or the pcb.
The positive wire and pcb housing was completely dry when I pulled out the board to look under it.
I kept holding down buttons and the mod didn't let me clear the puff count. It only let me raise and lower the wattage, that's it.
The settings are very limited.
You have temp control, power mode, and auto mode. All three settings prompted the error messages, overloadd, check atty and new coil selection + and -
No matter what I pressed ohm's were not reading below .54 and not firing... I don't know if this has happened to anyone else, any suggestions would be greatly appreciated....
The positive wire and pcb housing was completely dry when I pulled out the board to look under it.
I kept holding down buttons and the mod didn't let me clear the puff count. It only let me raise and lower the wattage, that's it.
The settings are very limited.
You have temp control, power mode, and auto mode. All three settings prompted the error messages, overloadd, check atty and new coil selection + and -
No matter what I pressed ohm's were not reading below .54 and not firing... I don't know if this has happened to anyone else, any suggestions would be greatly appreciated....
Similar threads
