Okay my Buzz Pro nolonger will fire a carto or atty. When I screw one on the light turns to red inside. Powerizer I got from Mike and AWs both fail. Tried several cartos and attys. Any ideas? 801 cap.
Buzz Pro issue
- Thread starter Vermonster13
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
Complete this checklist and tell us your answere
Buzz Pro ,. I Pro , VvproV
troubleshooting check list
batteries charged ?? ( use a voltmeter if you have one , they should read 4.2 volts each )
Take off the atty /carto first
Do you have a RED LED light ?
DO you have a Blue Led light when the button is pushed.
DO you have a Blue led with the ATTY/CARTO ON the unit ?
Do you have BOTH red and Blue led lights ?
Do you get a blue led with the atty/carto ON but no vapor ?
other things you can try, if you mave a multimeter
1: What is the voltage output on each battery
2: while holding the button on your BP what voltage is it showing on the 801 cap?
3: What resistance is the carto measuring?
If the BP is working properly, you should have a red light with batteries installed. When you push the button, the light should go blue. If you are not getting a blue light, I believe that is a short (could be a bad carto, or the wire that connects the electronics to the bottomside of your 801 cap may be loose.)
Buzz Pro ,. I Pro , VvproV
troubleshooting check list
batteries charged ?? ( use a voltmeter if you have one , they should read 4.2 volts each )
Take off the atty /carto first
Do you have a RED LED light ?
DO you have a Blue Led light when the button is pushed.
DO you have a Blue led with the ATTY/CARTO ON the unit ?
Do you have BOTH red and Blue led lights ?
Do you get a blue led with the atty/carto ON but no vapor ?
other things you can try, if you mave a multimeter
1: What is the voltage output on each battery
2: while holding the button on your BP what voltage is it showing on the 801 cap?
3: What resistance is the carto measuring?
If the BP is working properly, you should have a red light with batteries installed. When you push the button, the light should go blue. If you are not getting a blue light, I believe that is a short (could be a bad carto, or the wire that connects the electronics to the bottomside of your 801 cap may be loose.)
Verm, I would have thought you'd have looked under the cap to check the wire and ring terminal 
Are you keeping the top cap clean, making sure no drips are getting in under the screw or cap?
Are you keeping the top cap clean, making sure no drips are getting in under the screw or cap?
Do you get the blue light without the atty on it when you push the fire button? And do you have a different top cap to try one it?
I have tried several. They work on the 801 adapter on my ProVari. There is a short in the Buzz Pro somewhere. I'll tear it down tomorrow and see what I find.
Verm, let us know how it goes. It could be that the o ring under the top cap screw is squished and letting the cartos short out. It could also be that your adapter is pushing the center pin on them in, so that they aren't making contact on your BP, altho I would think you'd still get the blue light but no vapor if that were the case.
When you take the top cap off, clean it real good.
When you take the top cap off, clean it real good.
Blue until the atty goes on is a happy open circuit.
Red once the atty is on means there is Connector Continuity, just that the regulator doesn't like what it sees.
Unlikely, but any chance the atties are lr and the pro voltage is set too high? (not sure what light you get for that)
Alternately, if the atties are ok, pro center screw might be too high for those atties. Try unscrewing one a little, see if it starts working..
Red once the atty is on means there is Connector Continuity, just that the regulator doesn't like what it sees.
Unlikely, but any chance the atties are lr and the pro voltage is set too high? (not sure what light you get for that)
Alternately, if the atties are ok, pro center screw might be too high for those atties. Try unscrewing one a little, see if it starts working..
DOn't know. Neither of my caps work and I'm still waiting on a response from NotCig.
Verm did you email Mike at his sales@notcigs email? If so you aren't going to hear back because he's been in Toronto all week. You need to use the "contact us" on the Notcigs site. Hate to disappoint you but I am the tech support now, not Mike notcigs@gmail.com
notcigs@gmail.com
- Status
