Can i put a ce4 clearomizor on an x6 battery? i havr tried google and nothing that specific had popped up. The cew has its connector pin or whatever hidden, and so does the x6 battery. However, the x6 battery has a lot of empty space between the connector pin thing and the wall of the battery. Ce4's go cheap, like 20 for 20 bucks on ebay, great for me to try out new flavors without mixing them. However i do not want to buy a single one until i have this whole mess figured out. Thank you so much for your reply, you will be saving me valuable time and money!
can i?
- Thread starter thekill
- Start date
- th_trl_thread_readers 0
- Status
Does your battery look like this? https://www.fasttech.com/products/3001/10005380/2046207
I believe it's called Transformer X6.
I don't think CE4 clearos are good enough to test new flavours out? Try Smok Tech mini RDA (not sure if it would fit tho, HELP?), single coil, minimal e juice consumption, to change flavour just blot out the wick with a kitchen towel (paper) and if you're feeling paranoid, just rinse it with water and dry it by pressing a paper towel on it. Good to go.
I don't think CE4 clearos are good enough to test new flavours out? Try Smok Tech mini RDA (not sure if it would fit tho, HELP?), single coil, minimal e juice consumption, to change flavour just blot out the wick with a kitchen towel (paper) and if you're feeling paranoid, just rinse it with water and dry it by pressing a paper towel on it. Good to go.
You can always get a little mini rda like the octopus, 10 bucks. Pop a 1.6-1.8 ohm coil a little cotton and vape. When your done remove cotton, dry burn, rewick, and try a new flavor. Price of cotton it cheap. Misread post and say first main comment about threads.
SMOKTech RDA Rebuildable Atomizer
SMOKTech RDA Rebuildable Atomizer
Not sure if OP would see this but after three weeks of use, I think, Bully Phoenix RDA is a better shot.
Smok mini RDA uses brass pins and the threading in the posts wear out after two and a half week's use, it lasted about 15 coil changes (which includes a 30 gauge kanthal twist that did most of the damage). Well that's the case when you want a good contact and used a pair of nose pliers to tighten it.
Bully Phoenix is a full stainless steel body, uses a screwdriver to tighten the screw, has a well to hold excess juice, Downside is that the airhole is just as big as the Smok RDA and since it's stainless steel, it's much harder to drill it to a bigger size. Comes with a generic plastic drip tip too.
http://www.gotvapes.com/images/bigbully_4.png
This is the one I'm talking about, here (update: local stores, this is a bit outdated stock) it sells about the price of Smok RDA. Check out the Big Bully too, probably a better shot; on second thought probably not, it doesn't seem to have a visible well (idk mine is the smaller one)
Peace V
Smok mini RDA uses brass pins and the threading in the posts wear out after two and a half week's use, it lasted about 15 coil changes (which includes a 30 gauge kanthal twist that did most of the damage). Well that's the case when you want a good contact and used a pair of nose pliers to tighten it.
Bully Phoenix is a full stainless steel body, uses a screwdriver to tighten the screw, has a well to hold excess juice, Downside is that the airhole is just as big as the Smok RDA and since it's stainless steel, it's much harder to drill it to a bigger size. Comes with a generic plastic drip tip too.
http://www.gotvapes.com/images/bigbully_4.png
This is the one I'm talking about, here (update: local stores, this is a bit outdated stock) it sells about the price of Smok RDA. Check out the Big Bully too, probably a better shot; on second thought probably not, it doesn't seem to have a visible well (idk mine is the smaller one)
Peace V
Last edited:
- Status
Similar threads
- Locked
