Carto compatibility

[andrewr623]

Hello all, I feel like a traitor even posting here as I am a Bloog user lol. But I had a question that I haven't been able to find a clear cut answer on.

I have been poking around looking for different accessories that I can use on my bloog batt's and I was wondering if the volt ce3's
Smokeless Image | The Best Electronic Cigarette would work on my current batt's without any problems or not? From what I have been able to find is that the threads are the same but that they are slightly different ohm's on the carts and I haven't been able to find whether or not the air holes in the carts line up right either. if I can't find an answer I'm not opposed to spending 10 bucks to figure it out myself, but figured that I would at least see if I could figure it out before I ordered them. Oh and one other question as well if I do end up being able to use the ce3's can I use and 510/808/901 drip tip on them?
thanks in advance

 

[propagandax]

The answer is yes for the ce3, should work fine. Dont know about the tip, never tied.

Sent from my Nexus 7

 

[propagandax]

O and I might mention that SI has all the same products or very similar to bloog but less expensive. I have had both and would go as far to say they are likely made at the same factory but nobody is going to confirm that.

Sent from my Nexus 7

 

[charlzrocks]

The SI products are "less expensive" not "cheaper". I hate that word "cheap", makes me think of hookers for some reason......

Anyways, not sure of the CE3's fitting drip tips, but I bought some inexpensive clear drip tips from Good Prophets that fit the SI cartomizers quite nicely.

 

[propagandax]

The SI products are "less expensive" not "cheaper". I hate that word "cheap", makes me think of hookers for some reason......

Anyways, not sure of the CE3's fitting drip tips, but I bought some inexpensive clear drip tips from Good Prophets that fit the SI cartomizers quite nicely.View attachment 189844

Excellent point, changed wording above

 

[charlzrocks]

Well done!

 

[andrewr623]

thanks guys!!! You have backed up most of my research I was mostly concerned about the ohm ratings I used to do car audio and ohm readings are a MAJOR thing and wasn't sure yet just how sensitive these things are yet and didn't want to get something that wouldn't preform the way I wanted or worse yet fry my battery. I think I am on my way to order some volt accessories!! Thanks for the replies and the response time!!!

 

[Konstantine]

What's wrong with hookers? I've never been with one but from the ones i see on the street they look better dressed than most other sluts on cafe's etc.

 

[andrewr623]

I have one other question about the ce3's does anyone know if you can drip straight into the breather hole like you can with a Bloog carto to try different juices? this is something that I have really become attached to being able to do with the bloog carts and was wondering if I still would with the new ones that I just ordered from SI

 

[awsum140]

If you are VERY careful with how much liquid you drip in, as in only one or, maybe, two drops, you should be OK. If you overdo it you'll get a mouthful of whatever liquid you are trying, yuck! I'd suggest just taking an unused carto and pulling the filler out so it can be used as a drip atomizer. Again, you have to be careful with how much you drip in there or it'll flood and make a mess

 

[homeprogreen]

Lmao. Tried that one. Turns out 8 drops is to many

 

[andrewr623]

Thanks awsum!I will pay with it and see what's up, I typically only drip like 3-4 drops at a time anyways so that shouldn't be a big issue, I was just concerned that I might burn it out due to a random design quirk out something.

And Hell I'm sure 8 drops is WAY to many lol.

 

[awsum140]

Given that you'll be dripping down the air tube, getting some liquid in the mouth is probably unavoidable. I'd still suggest the carto minus the filler over dripping down the tube of a CE3. Another alternative would be to remove the inner silicon sealand air tube from a CE3. That way you can drip directly onto the wicks and coil.

I took a carto and removed the outer wrap, leaving a stainless finish. Then cut it down with a Dremel and cutoff wheel to about a half inch overall length. Removed the remaining polyfill, ground the edges smooth and added the little drip style tip that comes with CE3s and made it into a drip atty. Works great on a manual battery to test flavors!

 

[andrewr623]

That's definitely an interesting idea, I don't have a dremel but I'm sure I could find a way to cut down a carto.....