Cartomizer NO LEAK - EASY FILL -- REVISION MOD (is the air chamber really needed?)

[crazyodaz]

a while back Royal Smokers had some sort of contest

Royal Smokers E2 V4 Cartomizer Contest!!

We like this new technology!
But, without dripping...we need to fill with a syringe or bottle.

Who can come up with a simple way to fill them?
Like the Condom Method that works so easily and quickly for regular Cartomizers.

The best idea that works will win $100.00 worth of product from Clouds of Vapor of your choice.

This contest will run until it is won! No time limit!
http://www.e-cigarette-forum.com/fo...1-royal-smokers-e2-v4-cartomizer-contest.html

​

the BEST solution for me was by member HAIRBALL

I take all 3 rings out. The 3rd one can be a little stubborn but it will come out. I fill by dripping juice down the sides until it reaches just under the edge of the top of the ceramic cup (you can see it when it's full). I replace only the flat "O" ring and the mouth piece. The 3rd cup looking type ring hits the trash. I don't have a problems with leaking as the 2nd ring you take out fits back in snuggly. I use a small precission screwdriver to remove all of these. This works the best for me on the go. I don't have time for syringes while I'm at work.
​

ok, but i always keep my inferno in my pocket on the go and i was still getting some leaks and mouth fulls of flavor and why would i throw anything away yet alone the main 3rd seal with its fancy notches that are a pain to put back on?

here is my solution

1) - take apart your 3 rings like hairball suggested (and while its apart -- might aswell do a tea-bag mod to replace the standard wick

(the white one is ring#1 - the skinny one is ring#2 -- the notched one is ring#3)


2) after the optional tea-bag mod -- we NEED to keep ring#3 but make it easy to fill --- so lets cut it down so its narrow --- cutting with pair of scissors works just below the notches -- we dont need theese ----



ok -- so my cut is not perfect (and prolly does not need to be -- you can cut it as straight as you want, but i think this way does act as a CATCH incase the element gets flooded -- notice i did not touch the center groove in seal

3) -- lets fill up your cartomizer with no seals in it

4) -- put ring #2 (skinny ring with bevel) first ---- make sure the bevel is facing toward the element

5) -- put your modified ring #3 in -- BUT PUT IT IN UPSIDE DOWN -- so that the flat end is against the ring #2 and the open grooves are up toward mouthpiece


6) -- put ring #1 in -- push it down a bit -- this will mesh all 3 rings togetherand leave NO AIR COLLECTION CHAMBER -- nice tight seal

i have used this modified method for over a week -- love it, to fill it back up -- take out the 3 rings and fill along side -- then place it back same way and vape away

and no more flooded juice in my mouth

hope this helps some folks -- not bad for a newbie member like myself



​

 

[dormouse]

Wild!

What I would like is someplace to press the dropper tip of your juice bottle and just drip juice in. Like a port that can be pressed open with the dropper tip.

 

[crazyodaz]

Wild!

What I would like is someplace to press the dropper tip of your juice bottle and just drip juice in. Like a port that can be pressed open with the dropper tip.

yea something like that i need to work on modding my bottle dropper --- maybe a 1ml without the needle to act as a "FILLER TUBE" or GOOSE NECK attached to the bottle itself

it is difficult to get the whole bottle inside the carto -- but seen a bottle mod somewhere --- and the 3ring idea is easy to take appart and fill on sides

one advantage i found with the tea-bag mod and the reason why i even mod my 2.4ohm carto's is the lack of airbubbles

hate them things