CE2-XL --FLUXomizer

[Silversmyth]

Hi all,

I ordered a box of CE2's for my eGo from Gotvapes.
Wanted to give them a try for their juice holding volume .
Anyone know how to fill these things???? lol
l tried the pipette and juice seemed to just run out batt end and not fill cart.
I took out the white tip first -per instructions--but can't get it to fill.

Thanks in advance for help

 

[Sorrid]

A little searching and you would have found these right CE2 vids right away.

YouTube - CE2 Clearomizer Easy fill plug & Tube removal How-to Gotvapes.com

YouTube - CE2 Clearomizer Cartomizer Tips - Gotvapes Fluxomizer

 

[dormouse]

I believe the intended way is with a special syringe tip through one of the holes in the inner cap.

 

[Rosco]

If after watching the videos, you still need help, ask again. Videos are great, but I do it somewhat different with 100% success rate.

 

[Rosa]

Hi all,

I ordered a box of CE2's for my eGo from Gotvapes.
Wanted to give them a try for their juice holding volume .
Anyone know how to fill these things???? lol
l tried the pipette and juice seemed to just run out batt end and not fill cart.
I took out the white tip first -per instructions--but can't get it to fill.

Thanks in advance for help

Yeah, watch the videos sorrid linked. I just got mine last night in the mail. I freaking love them, but I was like you and tried to do it without watching a video first -- mistake.

 

[Silversmyth]

Thanks guys

Sorry sorrid!!! The old man is not that smart i guess

 

[Rosa]

If after watching the videos, you still need help, ask again. Videos are great, but I do it somewhat different with 100% success rate.

What's your method?

 

[Irons]

A little searching and you would have found these right CE2 vids right away.

YouTube - CE2 Clearomizer Easy fill plug & Tube removal How-to Gotvapes.com

YouTube - CE2 Clearomizer Cartomizer Tips - Gotvapes Fluxomizer

Good vids, I'm not very adventurous messing with new stuff until I can watch somebody else do it first.

 

[IOU]

I have found it is easier to pull the whole plastic tube off, push out the silicon sealing ring, reassemble the tube then just drip to fill. You have to be careful not to get juice on the ceramic cup, because then it will run out the batt connector. Then just slip the two seals back in. These things are fantastic!

 

[Rosa]

I have found it is easier to pull the whole plastic tube off, push out the silicon sealing ring, reassemble the tube then just drip to fill. You have to be careful not to get juice on the ceramic cup, because then it will run out the batt connector. Then just slip the two seals back in. These things are fantastic!

I'm having a hard time getting the inner seal thing to go back in, is there a trick? When I try to squish it back in there it just pushes the whole works down.

 

[fray]

It is very important to put pressure on both ends when putting the seal back in. I found this out the hard way and got a handful of fluid in my palm when the workings fell out of the tube

 

[FantWriter]

I just use a syringe. I had to get a real needle because the little plastic one that came with them bends too easily, but they're like $3.00 for half a dozen at Tractor Supply, so it's no biggie.

The little holes for the needle are hard to see if they're any liquid at all above the silicone seal, but I took to it right off because it's so much less mess than dripping into a regular carto.

 

[Irons]

I just use a syringe. I had to get a real needle because the little plastic one that came with them bends too easily, but they're like $3.00 for half a dozen at Tractor Supply, so it's no biggie.

The little holes for the needle are hard to see if they're any liquid at all above the silicone seal, but I took to it right off because it's so much less mess than dripping into a regular carto.

I was just wondering about that, Thanks!~

 

[Stownz]

Bottle with 22gauge blunt tip needle on top
E-liquid Web Shop CN XL Cartomizer refill set

 

[Rudy33]

I'm having a hard time getting the inner seal thing to go back in, is there a trick? When I try to squish it back in there it just pushes the whole works down.

you have to make sure the plastic cylinder goes down all the way - over the threaded end. Be very careful because the wire breaks

I have not had luck taking them apart without pushing the silicone plug at the same time. I dont put the plug back in either and just put the little mouth piece back on and vape slow or get a mouth full of juice. If you put the plug back in you need to line up the groves with the wick. A wooden scewer (flat end) works the best for me.

 

[Stosh]

Easiest way I've found is to take your syringe apart, slip the 20-22ga steel needle past
the third inner seal around the ceramic cup. Squeeze juice into the syringe and put
the plunger back in, inject and remove. Vape-on!

 

[Sorrid]

I'm having a hard time getting the inner seal thing to go back in, is there a trick? When I try to squish it back in there it just pushes the whole works down.

Best way to avoid this is to put the CE2 on your pv while putting the cup seal back on. Not all of them need this but some do.

 

[alisab]

Easiest way I've found is to take your syringe apart, slip the 20-22ga steel needle past
the third inner seal around the ceramic cup. Squeeze juice into the syringe and put
the plunger back in, inject and remove. Vape-on!

Ahhh moment. I have been refilling the ce2's successfully in various ways but I think the syringe needle is the easiest and fastest - the only problem I have had was sucking up juice from the bottle with the needle I have 22 gauge but I do manage it. Your solution is perfect!

 

[FantWriter]

Re: $3.00 for half a dozen needles at Tractor Supply --
I was just wondering about that, Thanks!~

I wrote that on the fly. Looking at their website, i find it's $1.99 for a pack of five (I knew it was cheap and had more than I needed).

 

[hippiebrian]

I love clearomizers! I just got one of the syringes, 99 cents I think at Mad Vapes with the 20 guage blunt needle, also 99 cents, and fill them that way. No problems at all!