It only takes a little piece of thread to fix the problem... that's all...
I'll try to explain... at one time or another about clearomizers... you'll hear it said
that for some reason contact is not being made between the pin of the clearomizer
and the post of what battery or mod being used... the poor victims are told...
"get something and PULL out the pin of the clearomizer if you can"...
"But...be sure not to let the PIN end up touching the sides or you'll have a major short!"
Just guessing on my part... but I figure with approximately 4,000,000 (4 million) Vapors
out and about just in the USA... And how about at least 10 million more in Europe... YIKES!
' that might mean there's a MIGHTY few millions of
DOA... clearomizer laying in drawers or landfills somewhere just because a very
simple problem.... THE SUPPLIERS .... could have... or should have advise everyone
about to fix the SOLUTION to this problem... has always been around in the form of
a little piece of thread...
This what I mean...
It was about two weeks ago that I got my vape mail in with a total of 8 Newest Generation
Stainless Steel CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer ... The BEST of The BEST....
Except for one thing... like many other clearomizer... NONE OF THEM could or would
make contact (their pins) with the deep well POST of my MVP 2.0, Nor my Vision Spinners.
I really didn't think to much of or about it... I just got me my trusty SPOOL of THREAD
Opened up the bottom of each CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer
Took out their coil
Completely... Pulled the PINS out of each single one of them
Wrapped 12 TURNS of thread around the back of each Pin... used finger nail clips to cut the thread
AFTER making sure to tie knots...
Used my finger nail (thumb) to pack ...just a little push... of the thread against the back of the pin...
Put the pins back where they belonged...
NOTE: You really don't have to take them all the way out
to wrapped the thread around them... I do it either way...
Those pins are small... so watch out for the SOCK MONSTER... they have a way of getting away from you. gulp!!!
Then I just
Put the HEAD... aka the coil back in each of the CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer
And to this day VAPING away.... Not a single contact problem with ANY of my clearomizers of many types.
YES!.... You can do this to TOP COILS also... and they will push the PIN at the bottom of the clearomizer down. ...
I'll try to explain... at one time or another about clearomizers... you'll hear it said
that for some reason contact is not being made between the pin of the clearomizer
and the post of what battery or mod being used... the poor victims are told...
"get something and PULL out the pin of the clearomizer if you can"...
"But...be sure not to let the PIN end up touching the sides or you'll have a major short!"
Just guessing on my part... but I figure with approximately 4,000,000 (4 million) Vapors
out and about just in the USA... And how about at least 10 million more in Europe... YIKES!
' that might mean there's a MIGHTY few millions of
DOA... clearomizer laying in drawers or landfills somewhere just because a very
simple problem.... THE SUPPLIERS .... could have... or should have advise everyone
about to fix the SOLUTION to this problem... has always been around in the form of
a little piece of thread...
This what I mean...
It was about two weeks ago that I got my vape mail in with a total of 8 Newest Generation
Stainless Steel CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer ... The BEST of The BEST....
Except for one thing... like many other clearomizer... NONE OF THEM could or would
make contact (their pins) with the deep well POST of my MVP 2.0, Nor my Vision Spinners.
I really didn't think to much of or about it... I just got me my trusty SPOOL of THREAD
Opened up the bottom of each CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer
Took out their coil
Completely... Pulled the PINS out of each single one of them
Wrapped 12 TURNS of thread around the back of each Pin... used finger nail clips to cut the thread
AFTER making sure to tie knots...
Used my finger nail (thumb) to pack ...just a little push... of the thread against the back of the pin...
Put the pins back where they belonged...
NOTE: You really don't have to take them all the way out
to wrapped the thread around them... I do it either way...
Those pins are small... so watch out for the SOCK MONSTER... they have a way of getting away from you. gulp!!!
Then I just
Put the HEAD... aka the coil back in each of the CE5-S BDCC (Bottom Dual Coil Changeable) Clearomizer
And to this day VAPING away.... Not a single contact problem with ANY of my clearomizers of many types.
YES!.... You can do this to TOP COILS also... and they will push the PIN at the bottom of the clearomizer down. ...
