[CLOSED]

[RobbieVape]

you could seal it with a short non-vented screw the same diameter as the 510 pin. Just screw it in the top of the tube

That is such a better idea than I last posted in using a a clamp or food bag sealer clip. Use the screw 2mm - 2.4mm I'm guessing and store them in a hard plastic box in your bag! Problem sorted


Sent from my iPhone using Tapatalk

 

[super_X_drifter]

you could seal it with a short non-vented screw the same diameter as the 510 pin. Just screw it in the top of the tube

That may be a great idea. Thank you. I was wondering about putting something under the cap. Any ideas anyone.

 

[RobbieVape]

Oh boy, Hope that CM v3 works out for you my brother. I wrap all of my coils using one of these...

I have a CM v2 I mainly use but also a cheap silver mandarin similar to yours to aid in placement.

I also recently bought two of each 100mm long 2.5&3.0mm smooth steel rod and same size again threaded rod.

The threaded rod is perfect for building TC temp coils spaced just following the thread

Sent from my iPhone using Tapatalk

 

[RobbieVape]

That may be a great idea. Thank you. I was wondering about putting something under the cap. Any ideas anyone.

Cling film easy choice won't look the best best double it up or measure the hole and get a nylon nut and bolt, have bolt on outside, use a rubber washer on inside. 11 bottles you could have three or four if the caps made this way

Edit meant have nut on outside


Sent from my iPhone using Tapatalk

 

[RobbieVape]

Cling film easy choice won't look the best best double it up or measure the hole and get a nylon nut and bolt, have bolt on outside, use a rubber washer on inside. 11 bottles you could have three or four if the caps made this way

Sent from my iPhone using Tapatalk

Just realise my batteries always dying when talking with you [emoji6]

Not sure on hole size, those are m4, a flatter washer would also be better


Sent from my iPhone using Tapatalk

 

[distortoblotto]

I have a CM v2 I mainly use but also a cheap silver mandarin similar to yours to aid in placement.

I also recently bought two of each 100mm long 2.5&3.0mm smooth steel rod and same size again threaded rod.

The threaded rod is perfect for building TC temp coils spaced just following the thread

View attachment 475638View attachment 475639

Yes, always use a threaded rod when building for Genny's myself, otherwise almost exclusively a fan of pinched coils. ( eliminates the possibility's of hot spots)

 

[Loopy1224]

I see that there is a shipment from Apple Valley Ca. due here on Wednesday......hmmmmmm wonder what it could be? [emoji15] [emoji15] [emoji12] [emoji1] [emoji1] [emoji1]

Sent from my SM-N910V using Tapatalk

 

[AllPepperS]

I sent my brass girl for some lizard love [emoji4]


Tapatalk [emoji252]

 

[RiverNut]

I'm gonna do the same for my brass Tranny when the mini gets here. It's just too cool.

 

[AllPepperS]

Love my trannys, but in the brass went with the girl, for weight lifting ya know.

 

[super_X_drifter]

I don't blame ya'll. snake skin is bad ayuss

 

[YePsTeR]

Do I detect a little yellow in that Tmod?? (green....but we all know about the lighting issue)

 

[RiverNut]

Love my trannys, but in the brass went with the girl, for weight lifting ya know.

good choice lol. After I've used the brass tranny for a while, I'll pick up one of my wood squonkers and it feels like it's missing juice and a battery .
Gotta alternate arms with the brass so you create some bicep symmetry

 

[super_X_drifter]

Do I detect a little yellow in that Tmod?? (green....but we all know about the lighting issue)

No it is a reflection of the day glo tennis ball lookin Nike running shirt I'm wearing. This is billet 6061 alumimun wearing a snakeskin vest

 

[Tbev]

That's how you know how shinny it is..

Meanwhile. .
Some mini action

And check out the lizzard engraving under sniper

 

[super_X_drifter]

These nylon screws and nuts are perfect. Thank you again Robbie. Ace hardware. Just walked in and picked em up. One definitely wants a thin head screw or it will not clear the rim of the bottle when you go to screw the cap on

 

[super_X_drifter]

That's how you know how shinny it is..

Meanwhile. .
Some mini action

And check out the lizzard engraving under sniper

Hell yeah bro it's so shiny it sparkles like a diamond in sunlight. It's a chameleon too as evidenced by that picture - it assumes the colors of its surroundings.

A TMOD without snakeskin is the equivalent of a wife wearing pajamas to bed. . Just my opinion. It's off the chain.

 

[RobbieVape]

I'm considering just taking the mini plain with lizard then I can mirror chrome that one up like my 18650z with lizard that would look the nutz


Sent from my iPhone using Tapatalk

 

[Nautilusfan]

I have a CM v2 I mainly use but also a cheap silver mandarin similar to yours to aid in placement.

I also recently bought two of each 100mm long 2.5&3.0mm smooth steel rod and same size again threaded rod.

The threaded rod is perfect for building TC temp coils spaced just following the thread

View attachment 475638View attachment 475639

Sent from my iPhone using Tapatalk

Hmmmm I really like the threaded rod idea!!

 

[daveinleics]

I'm definitely checking out the lizard engraving under sniper