Coil build for Protank2 on 3.7 Mech Mod Help.

[penstyle]

Yes I need a good coil build for a Protank2 and sigelei 19 with 18650 Sony VTC5. At the moment I only have 31 gauge kanthal.

Reason for question.
Put a 1.2 ohm on MVP2 VV 4.2 no problem. Same 1.2 on sigelei 19 and get cotton burn hits at end of draw.
What to do with what I have?

 

[Retro68]

MVP is a regulated mod, sigelei 19 is an unregulated mech mod. Thats the reason for the burnt hits.

 

[penstyle]

MVP is a regulated mod, Sigelei 19 is an unregulated mech mod. Thats the reason for the burnt hits.

Yep, I understand that.

 

[penstyle]

If 1.2 ohm is too low for mech mod then how is it that people are going with much lower ohms?

 

[penstyle]

Not like I'm trying to sub ohm here.
Just wanted to know how to make the transition.
Maybe there is not enough wick area for the increase in power.
Not doable in the protank.

Maybe someone can point me in the direction I need.
At this point even some snide(slyly disparaging) remarks may help.

 

[k702]

Not enough juice getting to the wick. Try turning the silicone grommet inside the tank upside down. Its also possible you used too much cotton. It will swell when liquid is added, too much and it will choke off wicking. If the first doesn't work try wicking with a tad less cotton.

Not sure why it would burn unless the MVP fires a little lower than it says its firing.

 

[penstyle]

Not enough juice getting to the wick. Try turning the silicone grommet inside the tank upside down. Its also possible you used too much cotton. It will swell when liquid is added, too much and it will choke off wicking. If the first doesn't work try wicking with a tad less cotton.

Not sure why it would burn unless the MVP fires a little lower than it says its firing.

Thanks for the reply. I suspect I reached the limits of the MVP2 as well as the Protank.
A tad less cotton is an option, as all my chimney caps are upside down.
Only getting the burn if I take a vape longer than 2 seconds so what you said makes sense.
Guess I'm just cursed with wanting to know each devices limits before moving to the next.

Found this in another thread related to my question but not much else.

The clearos will work on a mech, but not as low ohm as other drippers, kayfun, ect...they won't deliver enough juice fast enough, so 1.5-2.0Ω usually work better.....

So if I built a 2 ohm coil why not just put it on the MVP2.
Cause as AFAIK using 1.5 to 2.0 ohm on a mech mod is not the next level.
I want to get to the next level, so I'm getting a more appropriate atomizer.
Are we in the coil building section. LOL

But seriously if anyone has more pointers on stretching the limits of the Protank, learning is fun.

 

[k702]

Thanks for the reply. I suspect I reached the limits of the MVP2 as well as the Protank.
A tad less cotton is an option, as all my chimney caps are upside down.
Only getting the burn if I take a vape longer than 2 seconds so what you said makes sense.
Guess I'm just cursed with wanting to know each devices limits before moving to the next.

Found this in another thread related to my question but not much else.



So if I built a 2 ohm coil why not just put it on the MVP2.
Cause as AFAIK using 1.5 to 2.0 ohm on a mech mod is not the next level.
I want to get to the next level, so I'm getting a more appropriate atomizer.
Are we in the coil building section. LOL

But seriously if anyone has more pointers on stretching the limits of the Protank, learning is fun.

http://youtu.be/ako6XnngIa4

You can really only do so much with the protank though. Its an every day tank, not really meant to even be rebuildable. Tanks in general have limitations. Even the kayfun

Good luck to you