Coppervape BF Mod
- Thread starter Layzee Vaper
- Start date
- th_trl_thread_readers 0
- Status
This is the size I measured:
$2.27 Rubber O-Ring Seals for E-Cigarette (50-Pack) 50-pack - 12*1.5mm (D*T) at FastTech - Worldwide Free Shipping
I don't have them yet, to be sure tho.
The "no atty" kits I ordered had a spare in the box.
It's the same as on the 6ml REO Reo Grand bottles.
6ml Bottle cap o ring
Which is 3/8"ID X 1/2"OD X 1/16"CS
(Would be 9.5mm ID x 12.7mm OD x 1.5mm CS. 12 mm OD and 1.5mm CS would work)
-012 N70 Buna-N Nitrile 70 O-ring [B70012] : The O-Ring Store LLC, We make getting O-Rings easy!
Actual: 0.364"ID X 0.070"CS
Metric: 9.25mm ID X 1.78mm CS (OD is 11mm)
Minimum order of 17 from the o-ring store, but shipping hurts you ($5.60 1st Class, $9.50 Priority Mail)
This pack of 100 from Grainger are a bit pricey (8.5 cents each) but you could probably pick them up at a near by store in a day or two.
GRAINGER APPROVED Round Medium Hard Buna N O-Ring, 10.0mm I.D., 12.0mmO.D., 100PK - 1RHZ5|1RHZ5 - Grainger
If there's a hydraulic shop around you could grab Hercules 568-012 (70d, or you could get the 90D) or MOR-9x1.5 (metric size, listed as Nitrile rubber)
I need to get some 7mm ID o-rings (I think that's right) for under the atomizer, in various cross sections to stop leaks and align various atomizers w/o having to adjust the the pin i the mod.
Last edited:
Got Nectar Micro V2 RDTA converted to bottom feed and vaping away. Flavor is great, much like a smaller atty, and especially smooth. Air comes in from the side, accross the coil, and into a center tube which extends up to the bottom of the drip tip. Really no possibility for spitting with this design. I would like a slightly easier draw for restricted DTL, so next build will probably be a smaler diameter coil with slightly lower resistance. Gonna keep it this way for awhile though.
Head of the Fatdaddy squonk pin is a little thick. Will need to grind it down a half mm or so the atty sits right.
Head of the Fatdaddy squonk pin is a little thick. Will need to grind it down a half mm or so the atty sits right.
Cool!
Now that I think about it, I think I have a Nectar Micro somewhere in the back of the Vape drawer. Might have to do some Digging and see what is what.
If it's a V1 lemme know if it looks convertable. Not sure about that one.
So, after a bit over a week more time, I was really having trouble getting a consistent vape. Sometimes hard hitting, sometimes wispiness worse than a 5 ohm protank coil on an ego. At first, I thought it was me. Never had any luck with drippers that I have tried before, on any mod.
After a bit of digging(thank you ECF), and a bit of fiddling, the only conclusion that I could come to was that the 510 wasnt always getting contact(worked differently depending on how it was held). I solved that with a #60 o-ring from Home Depot. Now, perfectly consistent, with less than a papers thickness of space beneath the atty. I have also switched over to a 8 wrap 28g 3/32id coil, from the previous twisted coil. Close to the same flavor, just as much vapor, and better battery life (although I am still waiting for final judgement on longevity).
All in all, an A+ in my book.
Can't seem to be able to figure out a pic lately, but about 4mm shorter, and 2 mm or so thinner/narrower than my beloved Kato/KFL+ combo. A good 2 oz lighter too.
After a bit of digging(thank you ECF), and a bit of fiddling, the only conclusion that I could come to was that the 510 wasnt always getting contact(worked differently depending on how it was held). I solved that with a #60 o-ring from Home Depot. Now, perfectly consistent, with less than a papers thickness of space beneath the atty. I have also switched over to a 8 wrap 28g 3/32id coil, from the previous twisted coil. Close to the same flavor, just as much vapor, and better battery life (although I am still waiting for final judgement on longevity).
All in all, an A+ in my book.
Can't seem to be able to figure out a pic lately, but about 4mm shorter, and 2 mm or so thinner/narrower than my beloved Kato/KFL+ combo. A good 2 oz lighter too.
This is what Always made me Smile about Mech Mods.
The Ability to Fix/Modify them using Simple, Off the Shelf Parts, that can be found at a Local Hardware Store.
I dug out my Nectar Micro v1. Its No Go.
Not surprising with the center air. Oh well, next project.
FIY, CV friends, got these in last week and they're not bad. Downside: not SS like Fatdaddy. Upside: juice hole is 1.5 mm and they're 5 for $2.25. Bottom photo next to CV pin.
$2.25 Replacement Brass Contact Screw for GOON LP Atomizer (5-Pack) 5-pack - w/ allen keys at FastTech - Worldwide Free Shipping
$2.25 Replacement Brass Contact Screw for GOON LP Atomizer (5-Pack) 5-pack - w/ allen keys at FastTech - Worldwide Free Shipping
M2.5 x 7mm (threaded area) with a 2mm thick screw head.
M2.5 x 5mm
FDV M2.5 is 9mm w/ 2.5mm thick head
The stock pins work well enough for me, so I think I'll stick with them. Getting the pins from FD didn't work out, so I'll get another spare kit or two in case I need a pin.
Fasttech is having a 15% off flash sale for anyone looking to save a few bucks on a Coppervape or bottom fed atties.
Code is Redpacket
Discount is good until Jan 27
Code is Redpacket
Discount is good until Jan 27
My Goon 24 arrived today and I love it! Can't wait till the squonk pin arrives tomorrow for it.
Sent from my LG-H910 using Tapatalk
Sent from my LG-H910 using Tapatalk
Pulled from posts on FT.
I just hope FDV recovers, I like the SS pins better.
Still no M3 pins at FT either.
Last edited:
- Status
Similar threads
