Coppervape BF Mod

[benley73]

So eventually got around to a little tester build ,
Origen little 16mm , dual 28g SS 316l Vertical builds , actually works pretty well and can give some nice clouds ,
Good Flavours Using
Fryd Cream cakes

Sent from my ONEPLUS A3003 using Tapatalk

 

[benley73]

2nd build , Oumier Wasp rda 22mm
Flat wire core SS,32g wrap SS ,
0.47
20w - 38w nice an tastey not hot spaced build help so no spitting up tip
Now need to adjust the 510 on my CV bf for these 2 , both have flatter bf pins

Sent from my ONEPLUS A3003 using Tapatalk
Can collect a little condensation on top of the posts , over time , but nothing that causes problems

 

[benley73]

All the Coppervapes fans , you really need to try the Skyline from them , its fantastic build quality ,

Sent from my ONEPLUS A3003 using Tapatalk
Flavours are phenomenally good

 

[Rathamar]

All the Coppervapes fans , you really need to try the Skyline from them , its fantastic build quality ,

Sent from my ONEPLUS A3003 using Tapatalk
Flavours are phenomenally good

How is the draw on it? Is it really airry or more restricted?

 

[inswva]

The Skyline uses interchangeable peek airflow inserts. I imagine you could go as little or big on the airflow as you want.

 

[benley73]

The Skyline uses interchangeable peek airflow inserts. I imagine you could go as little or big on the airflow as you want.

Draw is user dependent , you get 10 disks if you choose the 8 extra one for 5usd , these are 8euro each for Original and then shipping ,

Sent from my ONEPLUS A3003 using Tapatalk

 

[benley73]

TBH is probably one of the easiest and best single coil rta ive vaped , , it just edged out the Hussar and Squape X

Sent from my ONEPLUS A3003 using Tapatalk

 

[zoiDman]

15mm Chamber on a 22mm rda?

I saw this Today on FT. Kinda Trippy looking. But maybe a Good Single Coil Flavor Chaser for 10 Bucks?

$9.54 Mulciber Styled RDA Rebuildable Dripper Atomizer - 22mm / 316 stainless steel at FastTech - Worldwide Free Shipping

Here is a Review of the Authentic ...

 

[inswva]

15mm Chamber on a 22mm RDA?

I saw this Today on FT. Kinda Trippy looking. But maybe a Good Single Coil Flavor Chaser for 10 Bucks?

$9.54 Mulciber Styled RDA Rebuildable Dripper Atomizer - 22mm / 316 stainless steel at FastTech - Worldwide Free Shipping

Here is a Review of the Authentic ...

I had the authentic and it was fantastic. Single vertical coil is a breeze and it's a flavor machine.

 

[zoiDman]

I had the authentic and it was fantastic. Single vertical coil is a breeze and it's a flavor machine.

Very Cool.

I never thought about doing a Vertical in it. In the Cart it Goes!

 

[hazozita]

Nice! In my cart as well -- FT has a 15% off sale on July 4, so starting to build up the cart in preparation. (Code is FREEDOM).

 

[benley73]

Only just got my 1.0 Armour RDA , bf

Sent from my ONEPLUS A3003 using Tapatalk

IAI can bf too , might even try a mesh coil between posts ,hmm

 

[TheWestPole]

Quick and Dirty Coppervape 20700/21700

Was balking at buying a 21mm bit just for this conversion. Last night I took a second look and a few more measurements, and decided to just flip it and get it done. Battery goes over to the bottle side which is already 21mm; an 18mm bottle over to the battery side. Vestigial cutout, I know, but what the hell. Top plate is unchanged except for removing a half mm thickness from the contact screw head.

Vaping away on it now. Don't think I'll finish the mod until the Samsung 21700 ships. Might need to open the battery bore up a hair to accommodate it.

 

[TheWestPole]

Only just got my 1.0 Armour RDA , bf

Sent from my ONEPLUS A3003 using Tapatalk

IAI can bf too , might even try a mesh coil between posts ,hmm

Nice. I don't have the other two, but got the Armor 1.0 last week and really like it. Only tried it single coil so far, but the flavor is so good I might just keep it that way.

 

[benley73]

Nice. I don't have the other two, but got the Armor 1.0 last week and really like it. Only tried it single coil so far, but the flavor is so good I might just keep it that way.

Its been built for single coils , really the deck plug curve s around each post to shut off one side properly ,

Sent from my ONEPLUS A3003 using Tapatalk

 

[Heartsdelight]

Quick and Dirty Coppervape 20700/21700

Was balking at buying a 21mm bit just for this conversion. Last night I took a second look and a few more measurements, and decided to just flip it and get it done. Battery goes over to the bottle side which is already 21mm; an 18mm bottle over to the battery side. Vestigial cutout, I know, but what the hell. Top plate is unchanged except for removing a half mm thickness from the contact screw head.

Vaping away on it now. Don't think I'll finish the mod until the Samsung 21700 ships. Might need to open the battery bore up a hair to accommodate it.


View attachment 668601 View attachment 668603 View attachment 668605

Damn you're good! What happened to the hole where the battery cover used to be?

 

[benley73]

Damn you're good! What happened to the hole where the battery cover used to be?

I thought same thing looks to be a different block , milled/ drilled out

Sent from my ONEPLUS A3003 using Tapatalk

 

[ST Dog]

What happened to the hole where the battery cover used to be?

Looks like a plate attached to the bottom (2 screws and vent hole under battery)

 

[TheWestPole]

What happened to the hole where the battery cover used to be?

Looks like a plate attached to the bottom (2 screws and vent hole under battery)

Right, covered by the bottom plate.

 

[zoiDman]

Quick and Dirty Coppervape 20700/21700

...

Outstanding West. Looks Great!

I've been Bugging CV to come out with a 20700 or 21700 version.