Difference between a kick and VV/VW?

Status
Not open for further replies.

Psionic

Full Member
Mar 16, 2014
18
3
Aptos, CA
I know a kick is a chip that goes inside a mech mod to allow boosting of volts/watts. What I don't understand is how it differs from a vv/vw mod which has a chip that does the same thing.

1. I know that vv/vw mods have ranges on how low you can set the ohms on your coils. Some wont allow lower then 1.5 ohms before it shorts the device and the newer box mods will allow you to go as low as 0.4 ohms.

2. As far as I understand, a kick will allow you to build below 0.4 ohms and boost voltage.

Why the difference when both are chips? Anyone know?
 

Baditude

ECF Guru
ECF Veteran
Apr 8, 2012
30,394
73,076
71
Ridgeway, Ohio
It depends upon what the manufacturer of the chips designs them for.

Keep in mind that to change the voltage/wattage of a regulated mod, you need only press a button.

With the Kick, a cross-thread screwdriver must be used to adjust the potentiator screw on the Kick to change the wattage. This requires disassembling the mechanical mod to get to the Kick. PITA if you happen to adjust your power a few times a day.

And since the Kick takes up some room in the battery tube, you may need to drop down in battery size.

Kick2.jpgSilver Bullet and Kick.jpg
 
Last edited:

Psionic

Full Member
Mar 16, 2014
18
3
Aptos, CA
It depends upon what the manufacturer of the chips designs them for.

I know that a kick requires removing the top cap of a mech mod and manually adjusting to increase/decrease the wattage output. What I don't understand is why there is no minimum ohms requirement on a kick. There is a min ohm level for vv/vw mods.

As far as I understand, both are chips. Why would chips in vv/vw mods have an issue with ohm levels and not a kick.

I agree that newer chips are going to allow for pushing resistance better but I am not aware of any vv/vw mods that will allow one to build under 0.4 ohms. Just wondering why?
 

Baditude

ECF Guru
ECF Veteran
Apr 8, 2012
30,394
73,076
71
Ridgeway, Ohio
As Nightshard said, both the Kick and regulated VV/VW circuit boards have protective circuitry designed to shut the device down for safety reasons, to protect itself, the battery, and the user.

Most regulated mods have an amp and watt limit. 3.5 amps and 15 watts for most regulated mods. They can fire a 1.2 and higher ohm coil.

The Kick 2 has a performance range in resistance of 0.5 - 3.0 ohm coils. The original Kick 1.3 - 3.0 ohm.
 
Last edited:

blueGrassTubb

Ultra Member
ECF Veteran
Verified Member
Mar 21, 2014
1,223
824
The Bluegrass
The real difference in between a Kick and a VV/VW MOD is that a Kicked mech MOD is bound to be worlds sexier than any VV/VW on the market.

I love my Sigelei 20W. It provides a very satisfying vape. But in comparison to my Akuma, it's "homely" looking. I can (nearly) the same performance from a MOD that is worlds better looking.
 

Baditude

ECF Guru
ECF Veteran
Apr 8, 2012
30,394
73,076
71
Ridgeway, Ohio
The real difference in between a Kick and a VV/VW MOD is that a Kicked mech MOD is bound to be worlds sexier than any VV/VW on the market.

I love my Sigelei 20W. It provides a very satisfying vape. But in comparison to my Akuma, it's "homely" looking. I can (nearly) the same performance from a MOD that is worlds better looking.
That my friend is in the "eye of the beholder".
 

blueGrassTubb

Ultra Member
ECF Veteran
Verified Member
Mar 21, 2014
1,223
824
The Bluegrass
That my friend is in the "eye of the beholder".

Yes.

I don't use a kick. I have regulated MODs for that.

I use both mechs and regulated MODs, and, in my own experience, mechs are worlds better looking than the vast majority of regulated MODs which are generally either plain boxes or plain tubes.

Some of the wooden regulated MODs are quite beautiful.
 
Status
Not open for further replies.

Users who are viewing this thread