Dual carb RM2?

[MamaTried]

I received a modded RM2 as part of a Reo I bought off the classies. It was described as: the remoizer 2.0 has 2 1/16" air holes...makes for an airy draw but produces TONS of vapor

I'm getting tons of... air.

Granted, the coil that is on it is only my second attempt at a coil, so there may be some user error involved.

Is there a secret to using an RM2 like this?

Here is my first attempt at making it vapable. It helps a lot, but negatively impacts the stealthiness of my Mini 2.1

 

[Treebeard]

I received a modded RM2 as part of a Reo I bought off the classies. It was described as: the remoizer 2.0 has 2 1/16" air holes...makes for an airy draw but produces TONS of vapor

I'm getting tons of... air.

Granted, the coil that is on it is only my second attempt at a coil, so there may be some user error involved.

Is there a secret to using an RM2 like this?

Here is my first attempt at making it vapable. It helps a lot, but negatively impacts the stealthiness of my Mini 2.1

View attachment 234386

LMAO! Bro, that thing looks ridiculous on that mini. The tooth pic is epic.

 

[nerak]

A ring made from a cartos condom will slide right down and cover the holes. You can adjust it to cover all or part. A o-ring would also work.

 

[unloaded]

1/16" is too airy for me, I can't imagine two holes that size!

 

[johni]

There are methods of filling holes in atomizer caps. You could fill one and try it. If still too airy, fill the other and drill a new one.

 

[MamaTried]

thanks all

my spidey sense is telling me that RM2s modded like this aren't found all that much in Downtown ReoVille, and that plugging it up (one way or another) is the best course...

 

[bris1974]

A for effort! lol

 

[harley05]

I kinda agree on that. I was thinking that if you find a old dull drill bit, (5/64 should work if its a true 1/16 hole), then match the radius by grinding the shank end to round it off. Then just cut off 1/8 off that end and gently tap it into the hole with a cloth covered hammer. With a good polishing on the radius end before installing it, it could match pretty close. Idk, just a thought...

 

[Statistic]

thanks all

my spidey sense is telling me that RM2s modded like this aren't found all that much in Downtown ReoVille, and that plugging it up (one way or another) is the best course...

You have two options. Plug one hole or make two coils.

 

[Bob57]

 

[MamaTried]

I kinda agree on that. I was thinking that if you find a old dull drill bit, (5/64 should work if its a true 1/16 hole), then match the radius by grinding the shank end to round it off. Then just cut off 1/8 off that end and gently tap it into the hole with a cloth covered hammer. With a good polishing on the radius end before installing it, it could match pretty close. Idk, just a thought...

A newb's mind is a terrible thing to mess with...
-apologies to Dan Quayle


well, at least i hope you're just messing

 

[JC Okie]

^^^^I don't think he's messing. I can totally picture it, and it could work. OF course, so will an o-ring covering one hole....and it might not seem so much like building a skyscraper.....

 

[technicianx]

You should try a dual coil in it once. You may like it? Of course don't try it unless your sure you can build the exact same coil twice... I thought about putting in another hole, but I had a bit of bad luck with a igo L...

 

[gimmieshelter31]

You should be able to use JB Weld to close one of the holes with no adverse issues.

 

[ltrainer]

^^^^what he said. The Red and Blue JB Weld works great.

 

[johni]

Superglue will work also, just put a piece of tape inside covering the hole then dab a drop or two. Give it a minute to cure, remove tape.

 

[MamaTried]

so, i'm getting close to dealing with my dual-carb... (yeh, yeh, i'm a tad slow bought some jb weld, superglue and god knows what else.

after playing with the carto condom as Karen suggested, it seems i need to cover one hole and around half of the other to get it acceptable to me. i am content with my other unmodified rm2s, so even one 1/16" airhole seems too airy.

what's the size of the stock airhole? i'm guessing i will need to plug up both holes then drill or ream one out somehow? i'm also not sure whether the ending hole should be closest or furthest from the coil...

i'm torn between trying to resurrect this thing or just donate it to one of the coil gurus to further the REO University research into Non-Standard Coilage...

 

[debzcf]

i'm torn between trying to resurrect this thing or just donate it to one of the coil gurus to further the REO University research into Non-Standard Coilage...

I vote for donating it for the purpose of research.

 

[ltrainer]

Reoville requires a signed Form 223 for any donations to research. These forms are available at the clerks office on Friday night from 9-9:30 PM. The form must be notarized. The notary public is available every other Tuesday ( 2cd and 4th Tuesday of the month) from 1-2 PM at the town office complex. Thank you.

 

[ltrainer]

If you have problems with this you can write to the Complaint Department. Karen Nerak is the person in charge there. Thank you.