eGo ONE tank series – CLR coil

[DPLongo22]

I wouldn't dream about calling you anything bad, dear! It's a fun mod--mine just has a bad habit of turning itself off and it speaks Chinese only, but not everybody has this problem. It was a gift, so... you know what they say about a gift horse. The mod it really sturdy, light and it works.

If you like it, you may want to investigate further. I'm sure the chip has been improved.

Thanks, Katya, and I assure you that I took NO offemse...

Sent from my SM-G935V using Tapatalk

 

[Katya]

Thanks, Katya, and I assure you that I took NO offemse...

I couldn't find any information on firmware upgrades, but my mod came with a USB port (and cable), so who knows. Maybe they will offer upgrades, eventually.

 

[Winblows]

eGo ONE CLR - Kanthal A1 28ga, ø2.7mm, 7 wraps, 1.28ohm

my fresh coiled eGoTo

 

[Dieseler]

Anyone try the Rcomen Pico-s from fastech using clr coils not the rebuild able deck as i don't intend to use it for that purpose.
Would like to hear your experience with it and clr coils.
I made the purchase of one yesterday, i did view this video and read positive and negative reviews
on the fastech website.

 

[Sugar_and_Spice]

Anyone try the Rcomen Pico-s from fastech using clr coils not the rebuild able deck as i don't intend to use it for that purpose.
Would like to hear your experience with it and clr coils.
I made the purchase of one yesterday, i did view this video and read positive and negative reviews
on the fastech website.

I have been looking at that one myself for a while, but still haven' pulled the trigger. Am interested also in any responses that come in.

 

[Foggy Road]

my fresh coiled eGoTo

That is very pretty. Like the tiny Windows.

 

[motordude]

I used the wrong link :-( try this one: $18.63 Free Shipping Authentic Rcomen Pico-s RTA Rebuildable Tank Atomizer (Pico-s, 316 SS + PEI, Yellow (kit)) at m.FastTech.com

In the first pic, there's a piece on the far left that looks like a drip tip without an o-ring, then a piece that looks like a thick washer. The drip tip looking piece replaces the top cap of the CLR coil. The base of the CLR coil screws into the washer bit that is screwed into the base. At the far right of the picture, there's a pin that drops back through the base and makes contact with the base of base of the coil...

Sent from my SAMSUNG-SM-N910A using Tapatalk

I think this is what u guys are talking about.
Shawn mentioned it some time ago in the tp thread.
Maybe he can chime in.

 

[gerrymi]

Comparing the CLR coils and the GS Air, which is better for MTL vaping?

As a confirmed MTL Tootle Puffer...once I got my first CLR tank...I finished using all the GS Air coils I had purchased...threw my GS Airs out the window...and replaced them with eGo ONE Mega V2's...

Joyetech eGo ONE Mega V2 Tank

After looking further a few websites mention the ProCL head is compatible with the ego one series although not rebuildable.

Dies...Did you run across any info re whether the ProCL head would be compatible with the original (non-TFTA) eGo AIO's???

Joyetech eGo AIO Kit (D16 D19 D22)

Sounding like a broken record from last rant but i think they missed a larger crowd being tank size could have been bigger
Could go on and on such as dumping the proprietary battery and made it a tube mod with regulated head that accepts18650 batteries as basically this is a throw away device once battery goes bad .

Have you run across the eGo AIO Pro C?

4ml. tank and replaceable 18650...

eGo AIO Pro C - Joyetech

Vapecrawler


..

 

[Dieseler]

Geerymi -Dies...Did you run across any info re whether the ProCL head would be compatible with the original (non-TFTA) eGo AIO's???

Sorry Geery i have not seen anything mentioned about those as of yet.

 

[Shawn Hoefer]

I think this is what u guys are talking about.
Shawn mentioned it some time ago in the tp thread.
Maybe he can chime in.

Yup... that's it... what am I chiming in about? Sorry, but I've been at a show (and prepping for said show) and not been keeping up...

Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[DancingHeretik]

As a confirmed MTL Tootle Puffer...once I got my first CLR tank...I finished using all the GS Air coils I had purchased...threw my GS Airs out the window...and replaced them with eGo ONE Mega V2's...

Joyetech eGo ONE Mega V2 Tank

Thank you! I guess I'll give it a shot.

Does that come with CL or CLR coils?

 

[Dieseler]

I think this is what u guys are talking about.
Shawn mentioned it some time ago in the tp thread.
Maybe he can chime in.

Yes that link is the

Anyone try the Rcomen Pico-s from fastech using clr coils not the rebuild able deck as i don't intend to use it for that purpose.
Would like to hear your experience with it and clr coils.
I made the purchase of one yesterday, i did view this video and read positive and negative reviews
on the fastech website.

Shawn can you tell us your expeience with this tank Rcomen Pico-s tank and clr coils .

 

[Shawn Hoefer]

Yes that link is the


Shawn can you tell us your expeience with this tank Rcomen Pico-s tank and clr coils .

I like it better than the deck it comes with. I know the deck is VERY heat resistant, but it still bothers me lol...

Mine, however, is not the Rcomen Pico-S... it's an older 1:1 Pico clone. The fill ports are smaller, the deck wicking ports are raised, the air is tighter (there are 3 1.2 mm holes on one side only). All the way open, it's a very restricted DL. Closed down to 1 hole, it's a tightish MTL. I suppose if I used the smaller pin in the CLR, I could tune it a bit better, but I prefer the restricted DL over the MTL...

If I had one complaint, it would be the raised wick ports, but that is easily overcome. Ok... if I had another, I would like a better drip tip...

Still, for an RTA that can be built 2 ways... it's, IMO, worth it...



Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[DancingHeretik]

Thank you! I guess I'll give it a shot.

Does that come with CL or CLR coils?

Nevermind. I just ordered CLR coils to go with it.

 

[Dieseler]

I like it better than the deck it comes with. I know the deck is VERY heat resistant, but it still bothers me lol...

Mine, however, is not the Rcomen Pico-S... it's an older 1:1 Pico clone. The fill ports are smaller, the deck wicking ports are raised, the air is tighter (there are 3 1.2 mm holes on one side only). All the way open, it's a very restricted DL. Closed down to 1 hole, it's a tightish MTL. I suppose if I used the smaller pin in the CLR, I could tune it a bit better, but I prefer the restricted DL over the MTL...

If I had one complaint, it would be the raised wick ports, but that is easily overcome. Ok... if I had another, I would like a better drip tip...

Still, for an RTA that can be built 2 ways... it's, IMO, worth it...



Sent from my SAMSUNG-SM-N910A using Tapatalk

Thanks thats encouraging and noticed no mention of leakage.The video i posted shows yours and the pico-s which is claimed improved due to changes made to airhole size and now on both sides, wick port lowered and they are no longer slotted etc.
Time will tell how i personally like it
and if anyone else would like to chime in on their experience that would be nice as well.

 

[Sugar_and_Spice]

As a confirmed MTL Tootle Puffer...once I got my first CLR tank...I finished using all the GS Air coils I had purchased...threw my GS Airs out the window...and replaced them with eGo ONE Mega V2's...

Joyetech eGo ONE Mega V2 Tank





Dies...Did you run across any info re whether the ProCL head would be compatible with the original (non-TFTA) eGo AIO's???

Joyetech eGo AIO Kit (D16 D19 D22)




Have you run across the eGo AIO Pro C?

4ml. tank and replaceable 18650...

eGo AIO Pro C - Joyetech

Vapecrawler


..

Yes, it has been established that the clr coils will work with this. However, since there is no base to this tank(as it only screws right onto the mod) I dont think many are that interested in it. I am wondering if the base of an eGo mega would fit on the tank. Are you planning on getting one of these kits? If so, maybe you can tell us if the mega base would fit onto this tank.

 

[Jumpin' In...]

Anyone try the Rcomen Pico-s from fastech using clr coils not the rebuild able deck as i don't intend to use it for that purpose.
Would like to hear your experience with it and clr coils.
I made the purchase of one yesterday, i did view this video and read positive and negative reviews
on the fastech website.

Please keep us posted on that tank! I'm concerned about the plastic tank, the too-small top o-ring and whether the draw can be tightened to my liking, but I really like the form factor of that tank. Short and stubby, like the GS-Tank and GS-MS.

 

[oplholik]

I am interested too, as I like the shorter tanks. I like to keep the length of a mod down.

 

[Dieseler]

Please keep us posted on that tank! I'm concerned about the plastic tank, the too-small top o-ring and whether the draw can be tightened to my liking, but I really like the form factor of that tank. Short and stubby, like the GS-Tank and GS-MS.

Will mention about it when it comes .

 

[ChelsB]

Not sure if this has already been posted, but I'm definitely picking up another amor tank!

Sent from my iPhone using Tapatalk