Yes, I need to get more. I think it's just right!
I just rebuilt the coil, wow, super easy and fun!
eGo ONE tank series – CLR coil
- Thread starter pufZeppelin
- Start date
- th_trl_thread_readers 0
- Status
Yes, I need to get more. I think it's just right!
I just rebuilt the coil, wow, super easy and fun!
all right - now were talkin'
was wondering if you might like the bigger air hole of the .5Ω
but if you-be-happy @ the smaller air hole of the 1.0Ω - all should be good...
That is super sweet!Yes, I need to get more. I think it's just right!
I just rebuilt the coil, wow, super easy and fun!
May I suggest Fasttech? They sell authentic Joyetech CLR coils for 7 bucks or so--and right now they still have a 10% off holiday coupon code REDPACKET--expires tomorrow!
Congratulations!
I was super excited because I got vape mail today! Bad part is that they sent me CL coils instead of CLR coils that I ordered!
Sorry.... Contact CS. And good luck!That hole is really big... I like a bit more air than the 1.8 mm, but 3.5 mm is way too much for me.
How do you rebuild it, Puff? Same resistance as the original? .5Ω?
Sound like you may have a connectivity problem with that one coil. Happens. I use Madvapes' circuit board spacers when this happens, but they are out of stock ATM. When/if they do restock, I suggest getting a few of those--they work great.
Circuit Board Spacer | Madvapes
seems I don't care for the closer to .5Ω builds (& lower)
I stay MOSTLY closer / just under 1.0Ω - like .8Ω .7Ω .99Ω 1.12Ω etc
then I have a 1.4Ω mood
but I just got used to the 3.5mm air hole and it is all the wife & me use (so means we can't even use the small hole anymore)
Grrrrrrrr. I'm getting dry hits. Juice flow wide open on a 1.5ohm 2.5mm kanthal coil with KGD cotton and 50/50 juice. 
Too much cotton. Cotton swells when it gets wet. If you make the cotton snug, and then it swells, no juice is getting to the coil. The cotton should slide smoothly through the coil, but still make contact everywhere...
Or, try Rayon... rayon doesn't swell...
Sent from my SAMSUNG-SM-N910A using Tapatalk
Or, try Rayon... rayon doesn't swell...
Sent from my SAMSUNG-SM-N910A using Tapatalk
Grrrrrrrr. I'm getting dry hits. Juice flow wide open on a 1.5ohm 2.5mm kanthal coil with KGD cotton and 50/50 juice.
sounds ' vapor-locked ' to me
take tank off, close air flow and cover with fingers - suck on it then WATCH to see bubbles rise ! !
might have to do it several times until ya get it in a good air ratio...
also try to put another cotton in it
Exactly! I have this same issue every other refill cuz my dumb .... refuses to stop filling until I've put in every drop that will fit! Then it locks up! I know better yet I STILL do it.
Yeah. I was very unhappy, initially, with the 3.2 mm AF hole on my Kayfun 5--now I like it, even though I still (and probably always will) do MTL. Funny how that goes.
What diameter coil do you make for those? 2.5 mm?
Grrrrrrrr. I'm getting dry hits. Juice flow wide open on a 1.5ohm 2.5mm kanthal coil with KGD cotton and 50/50 juice.
As my learned colleagues already pointed out, you're vapor locked.
Too much cotton, not enough airflow, or too much juice in the tank. Good luck.
Also, remember to juice up every new coil directly and let it saturate for a couple of minutes.
can't make up my mind which I like better, but it is always 2.5mm OR 3.0mm
biggest part is not anything with performance (between the two) but best/easiest to wick (yes, no kidding)
I struggle with consistency of making my wicks mostly 'cause I HATE TO WASTE (even tho I got a box the size of a dumpster)
I struggle with consistency of making my wicks mostly 'cause I HATE TO WASTE (even tho I got a box the size of a dumpster)
is right....I hate to waste, too.
- Status
Similar threads
- Locked
