Eleaf GS Air Fan

[IMRs]

 

[GranFumador]

Good afternoon All Airheads!! Rather quiet in here today for a Friday.
Here's some nice noise for your vaping pleasure!

And, having enjoyed that, here is something a little different, my former neighbor from before he became famous. Larry Coryell with Chico Hamilton, 1966

 

[aldenf]

Replying to myself, well, whadya know? It works!
Immensely complex and difficult procedure is accomplished as follows:
Use aviation snips to cut up to the side and bottom of one of the slots. Make another cut to the top of the slot on the other side of the slot far enough to be just wide enough for the wick and break metal off. Repeat on the opposite side. Smear tiny amount of epoxy on the two remaining slots. Let epoxy *fully* cure. Coil as usual and wick without trimming. Press cap back on and trim close but not flush with cap. Wet wick with juice to make sure it fills slot. That's it, GS Air CLR!

Pictures or it didn't happen! Really... can you help this exhausted mind in envisioning what you eloquently described? Thanks!

 

[IMRs]

And, having enjoyed that, here is something a little different, my former neighbor from before he became famous. Larry Coryell with Chico Hamilton, 1966

Wow, he introduced Larry! Pretty cool history.

 

[GranFumador]

Following our fine musical interlude... a vaping question.
Had a coil die of geriatric complications. Replaced it. Thoroughly washed and dried GS Air. Primed new coil á là Cheech. Filled tank. Put the pieces together and screwed them onto a 30. Yuck! Heavy duty industrial machine oil taste!
Tried the same new juice in another tank---very nice flavor.

Please offer recommendations for getting rid of the machine oil in a new coil.
Thanks. (Being of simple mind, I just vaped half a tank without inhaling, figuring the oil would burn off after a while. There has got to be a better way.)

 

[TrollDragon]

Sorry to hear about your dilemma. Hope everything is well over there. This is why I carry a larger man purse. You can't miss it when going out the door.

Thanks IMRs!
Cant really see myself with a man purse but a Lowepro or Pelican case works for me!

I'm surviving, the Silverplay has about 1.5 ml left and the locally made A.D.V in it is just too damn yummy!
The Rose is still half full of Flavor Crafters SuperNova.

Were ticking away the moments that make up a dull day...
And there are only 2 hours to go till I pick up the GS-Air!!

 

[Cheechako]

Following our fine musical interlude... a vaping question.
Had a coil die of geriatric complications. Replaced it. Thoroughly washed and dried GS Air. Primed new coil á là Cheech. Filled tank. Put the pieces together and screwed them onto a 30. Yuck! Heavy duty industrial machine oil taste!
Tried the same new juice in another tank---very nice flavor.

Please offer recommendations for getting rid of the machine oil in a new coil.
Thanks. (Being of simple mind, I just vaped half a tank without inhaling, figuring the oil would burn off after a while. There has got to be a better way.)

I have not had this happen...dunno.
maybe I like machine oil and didn't notice...might try boiling the coil?

 

[Cheechako]

Thanks IMRs!
Cant really see myself with a man purse but a Lowepro or Pelican case works for me!

I'm surviving, the Silverplay has about 1.5 ml left and the locally made A.D.V in it is just too damn yummy!
The Rose is still half full of Flavor Crafters SuperNova.

Were ticking away the moments that make up a dull day...
And there are only 2 hours to go till I pick up the GS-Air!!
View attachment 462006

I hope the Air lives up to your expectations and our extollations (is that a word @GranFumador?)
or should it be exhortations? Did we extort you into trying the GS Air M? Crap! the music confused me and with hints at Pink Floyd...
comfortably numb...

 

[TrollDragon]

To get machine oil out of all my atty's I break them down completely and shake a generous quantity of baking soda on the parts. Half fill the container with white vinegar and swish till the bubbling stops.

Then it is onto a good hot water rinse, soak in dish soap solution and rinse some more... It usually gets rid of machine oil without having to do a vodka soak overnight.

Don't think it would work the same with coils...

 

[IMRs]

Cant really see myself with a man purse

This is a very nice man purse, I must say.

Lanyards inside, if purchased at Walmart...

 

[IMRs]

maybe I like machine oil and didn't notice

That's great!!

 

[Cheechako]

Following our fine musical interlude... a vaping question.
Had a coil die of geriatric complications. Replaced it. Thoroughly washed and dried GS Air. Primed new coil á là Cheech. Filled tank. Put the pieces together and screwed them onto a 30. Yuck! Heavy duty industrial machine oil taste!
Tried the same new juice in another tank---very nice flavor.

Please offer recommendations for getting rid of the machine oil in a new coil.
Thanks. (Being of simple mind, I just vaped half a tank without inhaling, figuring the oil would burn off after a while. There has got to be a better way.)

Or throw it on the dead pile, send it to me and I will rebuild it for you. I have the hammer, the will and the attitude!

 

[Cheechako]

This is a very nice man purse, I must say.

Lanyards inside, if purchased at Walmart...

I never see that at wally world! the cooler is nice...

 

[LostVapeMonster]

Following our fine musical interlude... a vaping question.
Had a coil die of geriatric complications. Replaced it. Thoroughly washed and dried GS Air. Primed new coil á là Cheech. Filled tank. Put the pieces together and screwed them onto a 30. Yuck! Heavy duty industrial machine oil taste!
Tried the same new juice in another tank---very nice flavor.

Please offer recommendations for getting rid of the machine oil in a new coil.
Thanks. (Being of simple mind, I just vaped half a tank without inhaling, figuring the oil would burn off after a while. There has got to be a better way.)

Ugh. That happened to me with an I30 tank I bought. I tried EVERYTHING to get that taste out of the tank and it would not dissipate. Sorry to say, you might have to chuck it in the eff it bucket and move on.
I tried Vodka soaks, vinegar, Dawn dish detergent... none of it helped. I was peeved.

 

[IMRs]

I never see that at wally world! the cooler is nice...

You're killing me!

 

[crunchie812]

Pictures or it didn't happen! Really... can you help this exhausted mind in envisioning what you eloquently described? Thanks!

The fugly dark blob on the front is the JB Weld covering the slot. There's another on the back. The gooey things on the side are the wick ends protruding from the slots which have been widened and cut all the way down. HTH.

 

[LostVapeMonster]

Or throw it on the dead pile, send it to me and I will rebuild it for you. I have the hammer, the will and the attitude!

Are you doing rebuilds FOR us now???? If that's the case, Ima be saving up all my coils!

 

[Cheechako]

Ugh. That happened to me with an I30 tank I bought. I tried EVERYTHING to get that taste out of the tank and it would no dissipate. Sorry to say, you might have to chuck it in the eff it bucket and move on.
I tried Vodka soaks, vinegar, Dawn dish detergent... none of it helped. I was peeved.

Another vote for my hammer...

 

[Cheechako]

Are you doing rebuilds FOR us now???? If that's the case, Ima be saving up all my coils!

For you, anything!

 

[Cheechako]

The fugly dark blob on the front is the JB Weld covering the slot. There's another on the back. The gooey things on the side are the wick ends protruding from the slots which have been widened and cut all the way down. HTH.
View attachment 462010

It's alive!

Very cool!