Eleaf GS Air Fan

Status
Not open for further replies.

GranFumador

Ultra Member
ECF Veteran
Sep 12, 2013
1,607
17,647
Peoples' Bucolic Republic of Maine
Is the word we are looking for here possibly exaltation? :unsure:

1. a feeling or state of extreme happiness.
  1. "she beams with exaltation"
    synonyms: elation, joy, rapture, ecstasy, bliss, happiness, delight, gladness
    "a heart full of exaltation"
  2. the action of elevating someone in rank, power, or character.
Nope. Neither exaltations nor exhortations. The Master reBuilder meant "praise".
Context is everything. (But not even context will dissolve machine oil.:()
 

IMRs

Vaping Master
ECF Veteran
Verified Member
Sep 15, 2013
4,047
32,426
Penn's woods
How many beers have you had? :)
Since yesterday??
hilarious.gif
 

Cheechako

Vaping Master
ECF Veteran
Verified Member
Feb 11, 2012
5,192
39,314
Arizona
Nope. Neither exaltations nor exhortations. The Master reBuilder meant "praise".
Context is everything. (But not even context will dissolve machine oil.:()
PRAISE! yes, that's what I should have stated! We praise the GS Air...hope it lives up to it's praise.
 

crunchie812

Super Member
ECF Veteran
Verified Member
May 15, 2014
304
910
Key Largo, FL USA
I thought maybe it was the blob at first. :laugh:
namethatblobmelodypaul2.jpg
It just isn't very photogenic, it looks better in person than on camera. That said, I plan on using some clear, fast cure epoxy in the future. This was just a Q&D proof of concept, there is no need for the structural strength of JB Weld, it's what I had on hand. The JB Weld has to sit somewhere safe for a couple of hours while it hardens. Even with the quick epoxy I would let it set over night and bath in alcohol before using. It doesn't vape any better or worse than the wrapped coils, but for those who have a hard time with the wrapping it eliminates that step. I could prep about a dozen caps in fifteen minutes or so. Once it's done, it's done.

I'm on my second (MS) tank with no problems. If I continue with no problems I'll do 20 when the next slow boat from China lurches into the dock.
 

Cheechako

Vaping Master
ECF Veteran
Verified Member
Feb 11, 2012
5,192
39,314
Arizona
It just isn't very photogenic, it looks better in person than on camera. That said, I plan on using some clear, fast cure epoxy in the future. This was just a Q&D proof of concept, there is no need for the structural strength of JB Weld, it's what I had on hand. The JB Weld has to sit somewhere safe for a couple of hours while it hardens. Even with the quick epoxy I would let it set over night and bath in alcohol before using. It doesn't vape any better or worse than the wrapped coils, but for those who have a hard time with the wrapping it eliminates that step. I could prep about a dozen caps in fifteen minutes or so. Once it's done, it's done.

I'm on my second (MS) tank with no problems. If I continue with no problems I'll do 20 when the next slow boat from China lurches into the dock.

Sure would like to see the progression in pics or video...hint, hint! :)
 

Nanny22

Vaping Master
ECF Veteran
Verified Member
Jan 2, 2014
6,647
43,788
Michigan
Oh my gosh, you guys got busy in the last little bit here - for being a boring Friday!
We're talking high beams (I am so shocked it came back around!) and BEANS and toots.
Brought on I am sure by the cauliflower conversation --- BTW, I am making loaded mashed caulilfower as a side dish tomorrow with a birthday dinner for my son -- if you put enough bacon, sour cream and cheese into a dish, I have found it can be quite tasty.

This is also the second time in two days I have heard about Peanut Butter Jeasus and the Chalk Dust (sounds like a band from the 80s). I need to know if these are good -- there is a 20% sale right now at ejuices.com and I believe they have both, free shipping. Must be pretty decent - no?

I have my first GURGLING/FLOODING coil. Brand new out of the pack, with chimney - unless I let it sit for a few minutes between hits. Thoughts?
I am sure I am leaving out several things I wanted to comment on - so as Ahnold would say, "I'll be back".
 

Nanny22

Vaping Master
ECF Veteran
Verified Member
Jan 2, 2014
6,647
43,788
Michigan
I just open it up and clean out everything with a napkin and shake out the coil in the sink and it usually cures that Nanny. :)
I should have given more info -- that's what I've been doing and it keeps returning. I am wondering if I am screwing the coil down too tight, or maybe leaving it too loose. It's a 50/50 juice that has worked well in the Mtanks all along. Hate to pitch a new coil, but I just might. I have gotten spoiled to the perfection of the M - gurgling used to be so commonplace!
 

IMRs

Vaping Master
ECF Veteran
Verified Member
Sep 15, 2013
4,047
32,426
Penn's woods
I should have given more info -- that's what I've been doing and it keeps returning. I am wondering if I am screwing the coil down too tight, or maybe leaving it too loose. It's a 50/50 juice that has worked well in the Mtanks all along. Hate to pitch a new coil, but I just might. I have gotten spoiled to the perfection of the M - gurgling used to be so commonplace!
I guess the coil is overloaded with juice.
 

Nanny22

Vaping Master
ECF Veteran
Verified Member
Jan 2, 2014
6,647
43,788
Michigan
It will be fine Cheech, there are quite a few who use RBA/RTA gear like myself and sing the the golden praises of the Air! I think it will fit perfectly on my Kanger iPow2 pulling 8-10 watts off of it. I'll have to stop by the new juice shop on the way home and pick up a new flavor to celebrate.

If we could only get Cosmic Charlie's Chalk Dust - Peanut Butter & Jesus down here life would be grand. :drool:
I see it was TD who mentioned the Chalk Dust and PBJ -
Have you had both of these before TD? Sorry you can't get them now if they are a favorite! That would bug the snot out of me. What if someone was your middle man??
 

LostVapeMonster

The eyes are useless when the mind is blind.
ECF Veteran
Verified Member
Jun 7, 2011
3,109
20,596
58
Land of the Lost
I should have given more info -- that's what I've been doing and it keeps returning. I am wondering if I am screwing the coil down too tight, or maybe leaving it too loose. It's a 50/50 juice that has worked well in the Mtanks all along. Hate to pitch a new coil, but I just might. I have gotten spoiled to the perfection of the M - gurgling used to be so commonplace!
I have been so lucky with my GS Airs. No gurgling or flooding to speak of, with the exception of the one chimney-less coil I encountered. I may never use another coil/tank again!
 
Status
Not open for further replies.

Users who are viewing this thread