Eleaf GS Air Fan

[LynnNC]

Could be the rubber insulator or the housing insulator.

So either one or the other is toast and has to be replaced? And how do I know which one, trial and error?

 

[LynnNC]

He may have fell through the cracks of the new software

That's soooo funny!!!!! Lololololol

 

[Bikenstein]

So either one or the other is toast and has to be replaced? And how do I know which one, trial and error?

Does it read no atomizer?

 

[LynnNC]

Does it read no atomizer?

Yep! I've built 3 coils on it...none have read on the ohms meter.

 

[Bikenstein]

Yep! I've built 3 coils on it...none have read on the ohms meter.

If you assembled it correctly and put the metal pin back in it, then you should be getting a reading. If it's grounded out, you would still get a reading, even if it's 0 ohms...???

 

[LynnNC]

If you assembled it correctly and put the metal pin back in it, then you should be getting a reading. If it's grounded out, you would still get a reading, even if it's 0 ohms...???

I'll try it again in a few minutes. If I get the same thing I'm pitching it. Thanks for your help!!

 

[Bikenstein]

I'll try it again in a few minutes. If I get the same thing I'm pitching it. Thanks for your help!!

No trouble. Just inspect the insulators and everything as you assemble it. I always dry burn the coil before wicking it.

 

[Bikenstein]

Just built a coil for my first atty, a Kanger Evod. I drilled 2 of the air holes out to 3/64" and it did a lot for it. I gave some of these things away but didn't know I saved this one. Looks strange sittin on the SX.

 

[Bikenstein]

I'll try it again in a few minutes. If I get the same thing I'm pitching it. Thanks for your help!!

Maybe the rubber insulator is worn. Try pullin the metal tip out just a bit and then screw it back in the base. You should get a reading then.

 

[LynnNC]

No trouble. Just inspect the insulators and everything as you assemble it. I always dry burn the coil before wicking it.

Alright!! Another coil saved! I checked everything before I put it together, checked everything with each step...it works!!! Thank you!!

 

[Bikenstein]

Alright!! Another coil saved! I checked everything before I put it together, checked everything with each step...it works!!! Thank you!!

You're welcome Lynn. I was gonna suggest duct tape if that didn't work

 

[love coffee]

You can change your mood!!!! What a hoot this is going to be!!

How do you change your mood?

 

[IMRs]

How do you change your mood?

I think that's for supporting members only LC.

 

[love coffee]

I think that's for supporting members only LC.

 

[Oregon Linda]

I don't think the M is too warm at all. But I vape in the 8-10 watt range so YMMV.

 

[Bikenstein]

S

How do you change your mood?

Sometimes I'll have a drink or go for a ride...

 

[Cheechako]

Alright!! Another coil saved! I checked everything before I put it together, checked everything with each step...it works!!! Thank you!!

You have no idea what caused it Lynn?

 

[LynnNC]

You're welcome Lynn. I was gonna suggest duct tape if that didn't work

I might would have tried it! Lol

 

[LynnNC]

You have no idea what caused it Lynn?

No idea! Probably something I did wrong...

 

[Bikenstein]

No idea! Probably something I did wrong...

Maybe pushed the pin in too tight when you squeezed the cap on? I've had to pull a couple out a bit so they would contact the base. I avoid squeezing the pliers on the pin.