What ohms are you reading? If you're using a stock coil, then you may have blown one. And after you hit it, do you see bubbles floating up from the bottom of the tank? That will tell you whether it's wicking well or not?
Eleaf GS Air Fan
- Thread starter Javamon
- Start date
- th_trl_thread_readers 0
- Status
Yes. No leaking so far. Maybe I'm hitting it too often. The burnt taste seems to be coming mostly when I hit it back to back, so maybe I'm hitting it too hard, too often...
What kind of mod are you using?Yes. No leaking so far. Maybe I'm hitting it too often. The burnt taste seems to be coming mostly when I hit it back to back, so maybe I'm hitting it too hard, too often...
You're talking about the 1.5 ohm coils? Haven't taken one of those apart yet, but I have the 1.2 ohm vertical coils and don't remember an inner body on that one
Well if you're doing the same thing you've always done and it was seated sounds like a bad coil to me. Once a burnt taste always a burnt taste at some point. For me anyway. I have no tolerance for burnt.Yes. No leaking so far. Maybe I'm hitting it too often. The burnt taste seems to be coming mostly when I hit it back to back, so maybe I'm hitting it too hard, too often...
You are Right.
That tech I mentioned would Only work for Heads that have a Slotted Inner Body.
I've never tried the 1.2 ohm vertical coils. I'd just as soon rebuild the ones I have horizontal and use rayon because to be honest, I don't like the taste of organic cotton.
Well, what I was thinking doesn't even matter. Your other coils have been working for you. Sorry.
30g is only 45 bucks (while it lasts)
http://www.amazon.com/dp/B003E2Y2T6...&ascsubtag=10e6e138ff4d20617976807c331d2e60_S
http://www.amazon.com/dp/B003E2Y2T6...&ascsubtag=10e6e138ff4d20617976807c331d2e60_S
Hey I just Noticed Something.
I popped the Barrel off a 1.5 Ohm Head to check what was Inside. just like I remembered it. A Slotted inner body with a Horizontal Coil/Silica Wick.
OK...
So then I went to Pop Off the Barrel to a 1.2 Ohm. Ummmm... Not - Popping - Off - ? Three Tries with the Inverted Tank method later and No Pop. Screw that. Planets are in a Bad Alignment.
Tried a Nickel TC Coil. Same thing. What the Fluck is going on? Time for the LED Magnifier.
They're Different!
The 1.5 Ohm Barrel/Body is Different from the 1.2 Ohm and Nickel TC Barrel/Body.
I popped the Barrel off a 1.5 Ohm Head to check what was Inside. just like I remembered it. A Slotted inner body with a Horizontal Coil/Silica Wick.
OK...
So then I went to Pop Off the Barrel to a 1.2 Ohm. Ummmm... Not - Popping - Off - ? Three Tries with the Inverted Tank method later and No Pop. Screw that. Planets are in a Bad Alignment.
Tried a Nickel TC Coil. Same thing. What the Fluck is going on? Time for the LED Magnifier.
They're Different!
The 1.5 Ohm Barrel/Body is Different from the 1.2 Ohm and Nickel TC Barrel/Body.
now, now, tweety!i know you know that's an oversimplification! and depending on the coil resistance, even downright off
It's a simplification, of course, and I should have specified that it only works in our (my) tottle puffing range. So, let me restate: if you're vaping at 5-22 watts or so, using a typical 1.2-2.2Ω atomizer, an increase or decrease of .1v will increase or decrease your wattage by .4-.6 watts.
Test it yourself if you don't believe me:
Online Conversion - Ohm's Law Calculator
Finally got my GS Air tank today!
Of course, the first thing I did was to try and put on an Ego ONE Mega tank base with CLR coil on it. Nope! Does not work! Argh.,... I had this slight hope it would fit.
However, this tank is cute!
It is going through vodka bath right now and will try it tonight in TC mode.
Of course, the first thing I did was to try and put on an Ego ONE Mega tank base with CLR coil on it. Nope! Does not work! Argh.,... I had this slight hope it would fit.
However, this tank is cute!
It is going through vodka bath right now and will try it tonight in TC mode.
- Status
Similar threads
