Electrical Engineering Degree?

Status
Not open for further replies.
Am I the only one that feels like they have to go back to school and get an Electrical Engineering degree?

All of this talk about ohms and voltage is very overwhelming for someone who does not understand it.

Can someone explain all of the electrical jargon and why it matters? Or at least give a link where it is already explained?

Thanks!
 

tj99959

ECF Guru
ECF Veteran
  • Aug 13, 2011
    15,116
    39,600
    utah
    Rest assured that there are those that do understand this stuff. So stick around and they will do all the work for you.
    But this will help;
    Ohm's Law Calculator

    And this is what that little calculater can do for you
    ohmlaw.gif


    P= Watts
    E= Volts
    I= Amperage
    R= Resistance

    So it's just math, engineering skills are not needed.
     
    Last edited:

    Bradder

    Am I Chip or am I Dale?
    ECF Veteran
    Verified Member
    Jan 12, 2011
    1,136
    554
    71
    North Carolina, USA
    Hi and welcome! It is important if you want to use the different mods. Other than that the mah kind of tells you how long your battery will last before you need to recharge it. THAT is important!

    And if you don't even want to think about that, it usually breaks down into the larger (longer or fatter) battery lasts longer :) before needing charging. If you get a full starter kit and stick with the replacement parts that came with the kit, you'll be fine.

    I don't like to fool with it either and I was a math/science major :blush:
     

    Maestro

    Super Member
    ECF Veteran
    Feb 19, 2012
    912
    1,141
    Windsor, Ontario
    Its' easier if you understand the relationship between voltage, resistance and amperage. Think of your kitchen sink where voltage is water pressure, amperage is the amount of water flowing and resistance is the faucet. Increase the resistance (close the faucet) and you decrease the water flow (amperage). Increase the pressure (voltage) and you increase the water flow. Once you understand how the relationship works, the whole thing begins to make sense.
     
    Last edited:

    bulldogz

    Full Member
    Mar 20, 2012
    37
    27
    North Carolina
    Am I the only one that feels like they have to go back to school and get an Electrical Engineering degree?

    All of this talk about ohms and voltage is very overwhelming for someone who does not understand it.

    Can someone explain all of the electrical jargon and why it matters? Or at least give a link where it is already explained?

    Thanks!

    You are sooo not alone....I can't even seem to order cartomizers because you have to chose a "resistance" 2.4 ohm or 2.8 ohm and I am "degree-ed" too...smh:confused:
     

    DC2

    Tootie Puffer
    ECF Veteran
    Verified Member
    Jun 21, 2009
    24,161
    40,974
    San Diego
    More power = More heat

    More heat = More vapor
    More heat = Warmer vapor

    More power (Watts) = Less resistance (ohms) and/or more voltage (volts)

    Too much power = burnt tasting juice
    Too little power = wisps of cooler vapor

    This calculator can help you figure out the Power (watts) based on Voltage and Resistance (ohms)...
    Ohm's Law Calculator - of which there are many out there

    The sweet spot for most people seems to be somewhere between 6 and 8 watts of power.
    Many people (me for instance) like even more than 8 watts.

    I like to vape at around 10 watts.
    But I like tobacco flavors and they tend to hold up better to high wattage.
    :)
     
    Last edited:
    Status
    Not open for further replies.

    Users who are viewing this thread