EVL Reaper V3 MTL (YFTK clone)

Status
Not open for further replies.

rifky

Super Member
ECF Veteran
Nov 2, 2014
380
503
Indonesia
Since YFTK provide MTL deck for the option. I think this is quiet interesting for MTL. To be honest I am dont have exp with YFTK. Is that I must pull the trigger or wait for ULTON or SXK? Thx
44869177_732420437101739_9210288475549466624_o__93221.1544127606.380.380.jpg
47167937_755290811481368_1318874810381500416_o__21675.1544131666.1280.1280.jpg
images (32).jpeg
 

Rcon

Full Member
Aug 11, 2016
61
286
This is another interesting tank, the genuine made in the UK. It comes in two 2ml versions, the DTL with a 2.7mm deck air intake hole and larger holes on the AFC ring, and the MTL version with a 1.8mm deck air intake hole and smaller holes on the AFC ring. Both versions are £99 each and DTL<->MTL conversion kits can be purchased for £20 I think it was. A 5ml tank conversion is also available for £25.

It's not been out long and the initial reviews are very positive, but I think a lot of these are from reviewers/influencers sent free tanks to test, so worth keeping that in mind.

The genuine looks very well made and I think fairly priced for a top end tank, and the conversion options are reasonably priced too. I nearly bought a genuine yesterday on impulse but he is not shipping again until the new year so I decided to hold off.

I'm worried the MTL deck air intake hole might be too big for tootle puffers like me, so I may actually get a clone to test first. In my experience SMJY kit has been solid enough in the past.

Definitely one worth keeping an eye on I think.
 

vapdivrr

Vaping Master
ECF Veteran
Verified Member
Jul 8, 2012
9,966
19,932
61
sarasota,fl
Had a couple authentic v1's and if the v3 is anything close, it will be awesome. I just didn't like the look and size of the v1, so I traded them off, but the v3 seems a lot smaller and is much more of a looker.

Sent from my SM-G960U using Tapatalk
 

raqball

Vaping Master
ECF Veteran
Verified Member
Jan 22, 2010
4,283
9,282
I have the authentic DL version and it's a fantastic tank!

Has juice control that easy and simple and the build deck is easy-peasy. Wicking it kicked my .... a little and it took me 5 attempts to get it dialed in with the right amount of cotton...

I also got the 22<24mm beauty ring for mine.. EVL (I assume the clone will as well) also make adapters to covert MTL to DL or DL to MTL so you can buy one kit and convert it back and forth if you choose..

Highly recommend this sucker as it's a killer tank!

48420509-1176268729216540-1454907123409354752-o.jpg
 

rifky

Super Member
ECF Veteran
Nov 2, 2014
380
503
Indonesia
I have the authentic DL version and it's a fantastic tank!

Has juice control that easy and simple and the build deck is easy-peasy. Wicking it kicked my .... a little and it took me 5 attempts to get it dialed in with the right amount of cotton...

I also got the 22<24mm beauty ring for mine.. EVL (I assume the clone will as well) also make adapters to covert MTL to DL or DL to MTL so you can buy one kit and convert it back and forth if you choose..

Highly recommend this sucker as it's a killer tank!

48420509-1176268729216540-1454907123409354752-o.jpg
How to turn juice control? Its seem screw tight with 510 pin.
 
  • Like
Reactions: stols001

raqball

Vaping Master
ECF Veteran
Verified Member
Jan 22, 2010
4,283
9,282
How to turn juice control? Its seem screw tight with 510 pin.

I assume the clone is the same.. If it is then:

There is a ring on the inside that control juice flow...

Turn the tank clockwise to shut off juice flow. Turn the tank counter clockwise to open juice flow. When the V in EVL is over the air hole juice flow is open.

To remove the tank and access the deck you close air flow, then turn the tank to an in-between open and close position. You'll feel it disengage then pull upwards to access the deck..

It's brilliant and works great..

The only issue that may arise with the clone is IF they properly put the EVL markings where they belong. Lining up the V with the air hole makes it easy to see that juice flow is open. If they marked it incorrectly, then that won't be the same..
 
Last edited:

raqball

Vaping Master
ECF Veteran
Verified Member
Jan 22, 2010
4,283
9,282
For those curious about the Reaper V3, how it works ect here are a few images I did of a build today.

In the 3rd photo you'll see the white ring on the inside.. This is for juice flow to the wick. You set it by moving the ring. In the photo shown I have it wide open to the juice ports. One you complete your build it can still be adjusted, just not with the tank together..

In the 2nd, 3rd and 4th photo you see the lip in the base. When attaching the tank to the base you line up the V in EVL centered on the lip and push down. This assumes the cloners properly mark/stamp the clone that is but this is how the authentic works.

Once the tank is assembled and on the mod, turning it clockwise will turn juice flow off. Turning it counter-clockwise will open juice flow up. An easy way to tell if juice flow is open is the V in EVL should be over the air hole. Again, this assumes the clone is properly marked / stamped...

To access the build deck you turn the tank mid way between open juice flow and closed. You'll feel the tank disengage, then just pull up...

To refill you can do it one of tow ways. Remove tank as described above then unscrew the chimney and fill or as I do, just turn the mod upside down and twist the tank portion off.....

Hope this helps...

6-IW9rnb4-Q5i5d40z-Q6-Mn-Bw.jpg


Nm-YIGR8-FQ7e-D2-Ek-UVCQc-Bg.jpg


4f46a-C8o-Q0-GALGW2z-Coz-A.jpg


o-P9-Iv-URc-RPS-w-BAFM-p-A.jpg
 
Status
Not open for further replies.

Users who are viewing this thread