General Discussion Thread..
- Thread starter MonsterKenny
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
I've been a bad girl again....lol
I get so comfortable here sometimes I forget that the rules aren't as relaxed as they seem and I overstep the language one when I'm joking around. It's my own fault, I know.
I own it, though. Full responsibility...lol
I get so comfortable here sometimes I forget that the rules aren't as relaxed as they seem and I overstep the language one when I'm joking around. It's my own fault, I know.
I own it, though. Full responsibility...lol
That sort of behavior generally merits a spanking! Oh wait, I better remember who I'm talking to...
(Sorry, couldn't hold out any longer. Waiting for my demerit...)
LOL I'm just incorrigible, I suppose.That sort of behavior generally merits a spanking! Oh wait, I better remember who I'm talking to...
(Sorry, couldn't hold out any longer. Waiting for my demerit...)
Really, it's all about fun, though. My life has been extremely hard so I tend to be a clown to the extreme.
I befouled the Female Vaper thread in General E Smoking Discussion. It is now a vast wasteland of deleted posts.Where did you commit this infraction?
Ok, change of subject...ProVape technical speculations...
So ProVape, are you using DMG CTX's or Mori Seiki NT's? Maybe Mazak Integrex? What about part design and programming? I'm guessing CATIA or UG NX...maybe SolidWorks with MasterCAM? (I betting on the higher end stuff because of the material and excellent finishes).
I would believe no more than two different sized conical ball mills for the outer engraving of the tubes and "droplets". Close?
Tolerances in the .001"-.002" range? Perhaps tighter?
So ProVape, are you using DMG CTX's or Mori Seiki NT's? Maybe Mazak Integrex? What about part design and programming? I'm guessing CATIA or UG NX...maybe SolidWorks with MasterCAM? (I betting on the higher end stuff because of the material and excellent finishes).
I would believe no more than two different sized conical ball mills for the outer engraving of the tubes and "droplets". Close?
Tolerances in the .001"-.002" range? Perhaps tighter?
Funny - this thread had 30 posts in it's first 2 months...
In comparison, since the old saloon closed - over 600 posts in the Migration thread in just 2 weeks!
We should though, "take care" of this forum - we don't want to cause trouble here, 'cause the vendor's gotta play mod...
In comparison, since the old saloon closed - over 600 posts in the Migration thread in just 2 weeks!
We should though, "take care" of this forum - we don't want to cause trouble here, 'cause the vendor's gotta play mod...
I never intend to cause trouble ANYWHERE. It just sort of...happens.
The migration thread sort of became the Saloon but I don't mind having more than one thread for fun.
I'm with you on that ZoeThe migration thread sort of became the Saloon but I don't mind having more than one thread for fun.
Of course we always DID mix in a lot of technical stuff into the Saloon so we could keep this one casual.
I'm not so sure I want to keep an eye on two forums. It's hard enough to stay up with ONE! Chatty bunch (and fun). What's the hold up with Provari Nation? I'm seeing ppl post questions about Provari in all sorts of places; general discussion, APV, etc. and most of those are looking for help. This vs that one type, stuff that doesn't really fit on a vendor's forum either. Kinda awkward.
I feel like I should ask this question in the other group. Too confusing.
I feel like I should ask this question in the other group. Too confusing.
I just made a bookmark to this forum on my bookmarks bar right next to my regular ECF bookmark and click one right after the other to see everything. Made it way easier, especially since the board isn't as busy as it was before the revamp. At least it SEEMS less busy now.
I contacted Ocey to find out where everyone was. I knew if anyone were informed it would be HER.
- Status
Similar threads
