General UFS Questions

[imeothanasis]

Very thoroughly and instructive videos.
But i was wondered did you manage to make that small trick to
AVS so it can take 10 ml of liquid?

UFS has one more ability that I forgot to mention and you just remind it to me Zu. It can be bigger than it is now by adding sleeves on it. So I can make sleeves in future and a new atomizer extension so you can have as much capacity of liquid as you want

 

[Caddyman]

Yes, this is my custom UFS, it holds about 500ML's

(joke, hah)

 

[Moshmarr]

Heh, only have to fill it a few times a year! LOL!
But seriously, good to know this option will be available. Have the (regular, not custom 900 ml lolz) UFS been shipped to suppliers yet?

-an eager awaiter

 

[zuTma]

@imeo
wow in fact very simple yet so ingenuous but i'm afraid
you're gonna have to make a tons of that sleeves and even more UFS-s because
of that "small" thing.
Like they say "The simple things are the best"
How can you even forget to mention this?! I think this is gonna be huge stuff
among GG users, and probably wider.

 

[imeothanasis]

Heh, only have to fill it a few times a year! LOL!
But seriously, good to know this option will be available. Have the (regular, not custom 900 ml lolz) UFS been shipped to suppliers yet?

-an eager awaiter

yes, it shipped today Mos

 

[imeothanasis]

@imeo
wow in fact very simple yet so ingenuous but i'm afraid
you're gonna have to make a tons of that sleeves and even more UFS-s because
of that "small" thing.
Like they say "The simple things are the best"
How can you even forget to mention this?! I think this is gonna be huge stuff
among GG users, and probably wider.

I sometimes forget to mention some important things Zu. Variable UFS was my first concern when I was trying to make a telescopic feeding system but as you see I forgot to mention it lol

 

[SparkyII]

A quick cartomizer question or two, folks - what kind of 510 cartomizer would theoretically work in the UFS? The ones with the polyester wool that you drip the juice directly onto? Aside from cutting it down to 510 atty length, what other prep work would need to be done? Removing all the wool? Just some of it? Are the holes in the screw section sufficient to feed juice up to the coil, or do I need to to widen them / drill others?

Cheers,

Sparky

 

[imeothanasis]

You need only the hole on the side Sparky

 

[SparkyII]

Really? Only the 510 cartomizer is about 12mm longer than the 510 atty...

 

[imeothanasis]

You said "Aside from cutting it down to 510 atty length", so I thought that you will do this anyway sparky

 

[jacktan12]

This is definitely digressing, but I made a stupid noob mistake and used a 1.5 ohm atty with 2xCR123 3.2V batteries. Forgot to change out the atty when I wanted to try 6V vaping for the first time. Super hot vapour......throat hit that can kill a cow from 18mg juice. Didn't pop the atty and it's still ok. Now I know what Imeo felt like when he did that video for sonabraham and did the same thing. Yikes.....24 watts is waaaayyyy too high. Cough....cough....

 

[Wylie]

Yikes. I think around 10 watts is my upper limit. I can't even really imagine that.

 

[jacktan12]

Yikes. I think around 10 watts is my upper limit. I can't even really imagine that.

Imagine it like this......DK Tab, heated to boiling point, and poured down your throat. That's what it felt like to me. Surprisingly, after about the first couple of drags, it got easier to handle. I used it in this way for almost half an hour before I gave up. No burnt taste at all, as I had the juice control turned up. Slight flooding for a single drag, but after that, it was wicking quite nicely. Not something I want to repeat again. Don't understand how Imeo can stand this.

 

[SparkyII]

You said "Aside from cutting it down to 510 atty length", so I thought that you will do this anyway sparky

Lol; I walked into that! I'll give it a go then. Won't this mean that the juice control won't work?

 

[imeothanasis]

Imagine it like this......DK Tab, heated to boiling point, and poured down your throat. That's what it felt like to me. Surprisingly, after about the first couple of drags, it got easier to handle. I used it in this way for almost half an hour before I gave up. No burnt taste at all, as I had the juice control turned up. Slight flooding for a single drag, but after that, it was wicking quite nicely. Not something I want to repeat again. Don't understand how Imeo can stand this.

Its because I vape at 6mg of nic buddy. If I vape a 18mg I would be dead right now lol

 

[jacktan12]

Its because I vape at 6mg of nic buddy. If I vape a 18mg I would be dead right now lol

I'm sure I would be dead if I vaped it this way for long. Half an hour was more than enough to put me on the floor. Maybe hifistud can last longer. I don't think any amount of nicotine content juice should be vaped at this wattage. Do not try this at home. We're professionals......

 

[Wylie]

A quick cartomizer question or two, folks - what kind of 510 cartomizer would theoretically work in the UFS? The ones with the polyester wool that you drip the juice directly onto? Aside from cutting it down to 510 atty length, what other prep work would need to be done? Removing all the wool? Just some of it? Are the holes in the screw section sufficient to feed juice up to the coil, or do I need to to widen them / drill others?

Cheers,

Sparky

JBTX1 showed me an alternative to use a 510 cartomizer connection on the UFS. I hope he weighs in on this.

Basically, you just get a Danco washer (I'll try to find a link) and just extend your 510 cartomizer through the lid of the UFS. I tried his and it worked great, but I haven't done it to mine, yet. Here are two pics, one in the UFS and one just showing the cartomizer and washer.




As I play around with it more, I'll make a thread.

Other: No, you don't use the atomizer extender and no, you don't need to put a hole in the carto.

 

[imeothanasis]

Do not try this at home. We're professionals......

xaxaxa, yes we are jack lol

 

[imeothanasis]

JBTX1 showed me an alternative to use a 510 cartomizer connection on the UFS. I hope he weighs in on this.

Basically, you just get a Danco washer (I'll try to find a link) and just extend your 510 cartomizer through the lid of the UFS. I tried his and it worked great, but I haven't done it to mine, yet. Here are two pics, one in the UFS and one just showing the cartomizer and washer.

very nice trick Para!.
As for the hole on the side of carto, does carto works without a hole? How liquid will come inside atomizer? Rethreater doesnt allow juice to come inside atomizer.

 

[Wylie]

very nice trick Para!.
As for the hole on the side of carto, does carto works without a hole? How liquid will come inside atomizer? Rethreater doesnt allow juice to come inside atomizer.

It's a 510 cartomizer in the UFS, so no re-threader is needed. It feeds like a regular 510 using the liquid control (no hole). Again, I only used JB's (which worked great), so I don't have it all figured out. Just showing the idea.