generations of the e cig and history

Status
Not open for further replies.

novamatt

Super Member
ECF Veteran
Verified Member
Jan 12, 2010
640
647
Washington, DC area
When I started vaping the first time in 2008 or so, the Joye 510 was the best thing available.

ecig-size-compare.jpg


It was a cigalike with cartridges and didn't (doesn't - they still sell them) wick very well. Because of that, people would sometimes just take the cartridge out and drip it directly on the atomizer (that's where the bridgeless 510 dripping atomizers come from). Other people experimented with different filler material in the cartridge - the most popular things were the blue foam from fish aquarium filters and pyramid shaped teabags. People would buy boxes of Lipton tea, cut the bags open, dump the tea, and stuff the bag into their cartridge. The batteries didn't last long at all, but it was cool - you'd buy two or three and carry them around in a charging case. It looked kind of like a pack of cigarettes, you charged it overnight, and when your battery died, you put it back in the case and a couple hours later, it would be charged up again.

As mentioned earlier in this thread, there were people modding flashlights and such, but I never got into it - not an electrical engineer and too concerned about safety.

The next big thing in professionally made e-cigs a few years later was the Ego, and shortly thereafter, tank systems (the Ego-T).

ego_t_e_cigarette_wholesale.jpg


Compared to what we had before, these things were awesome! They had these big batteries that lasted a couple of hours, and no more of that crappy filler stuff. The cartridge looked pretty much the same, but it was completely empty. You'd fill it with juice (held a little under 1ml), put the cap on, punch a hole in it, and put it on your device. The tanks lasted a lot longer than an old 510 cartridge. They were messy as hell, though. They'd leak all over your battery and/or your pocket and there was no way to fill the things up without getting juice all over your hands. The atomizers were pretty much the same thing as the earlier 510s, and you'd use them for a couple of days, then replace them with new ones. Attys were about $4 a piece.

Then came the Ego C. This was just like the Egos above, but instead of buying a whole atomizer tube for 4 bucks, you could take just the atty out of the tube and replace it with a new one (much like clearomizers now) and you could get a 5 pack of them for $10 or so, cutting the cost of attys in half.

ego%20c%20black-1.jpg


Then we started to see the things that are popular today - clearomizers, variable voltage like spinners and twists, and "Advanced Personal Vaporizers," which were basically what we know now as variable voltage mods.

And that pretty much brings us to the present. Does that help?
 
Last edited:

wv2win

ECF Guru
ECF Veteran
Feb 10, 2009
11,879
9,045
GA by way of WV
When I started vaping the first time in 2008 or so, the Joye 510 was the best thing available................

As mentioned earlier in this thread, there were people modding flashlights and such, but I never got into it - not an electrical engineer and too concerned about safety.

The next big thing in professionally made e-cigs a few years later was the Ego, and shortly thereafter, tank systems (the Ego-T)..........................

The Screwdriver was a approximately a year before any ego type PV. And it was sold and manufactured by a company in the UK. Then came the 5 volt Prodigy from Puresmoker, also in 2009:

Prodigy.jpg

And then came the GLV around the end of 2009, first of 2010:

glv2.jpg

There were quite a few good mods prior to the ego. The ego was actually quite "late" to the game.
 

novamatt

Super Member
ECF Veteran
Verified Member
Jan 12, 2010
640
647
Washington, DC area
The Screwdriver was a approximately a year before any ego type PV. And it was sold and manufactured by a company in the UK. Then came the 5 volt Prodigy from Puresmoker, also in 2009:

View attachment 337692

And then came the GLV around the end of 2009, first of 2010:

View attachment 337693

There were quite a few good mods prior to the ego. The ego was actually quite "late" to the game.

Right. But I wouldn't exactly call them mass produced or extremely popular. They probably had under 10% of the market, and the standard recommendation on the forums was "get an ego starter kit." I wasn't trying to ignore the mods, just give an overview of what the majority were using at the time. Mods didn't start to become mainstream for vapers until the variable ego stuff opened the average customer's eyes to what you could do with power control.

Heck, I just saw a post on the newbie forum from a guy that just bought an ego T kit. They're still relatively popular as starter sets.
 

Baditude

ECF Guru
ECF Veteran
Apr 8, 2012
30,394
73,076
71
Ridgeway, Ohio
How about another blast from the past. The AltSmoke Silver Bullet was one of the first mass-produced mechanical mods. Made from aircraft-grade aluminum and machined to a then unknown quality, the SB has aged well over the passage of time being nearly as popular to this day as it was when first introduced in 2009. This was my very first mod along with the AltSmoke BB (14500 mechanical mod) two years ago. Both are workhorses which I still use to this day.

Watch Grimm Green review the SB (2009) as he uses an 18650 mod for the first time, and vaping at 6 volts (2 RCR123 stacked) for the very first time.



clear&frosted-tank-1.jpgBella-Phin-Frog.jpgSilver Bullet with AGA T2.jpgbellafam006.jpg
 
Last edited:

im_coryy

Senior Member
ECF Veteran
Apr 1, 2014
297
134
USA
wow thanks guys this is all extremely interesting, we have truly come a long way just in the past two years it seems. lets hope that with the new regulations we arent going to take 7 steps backwards as vapers, hopefully nothing changes but we all know that wont happen. can you guys imagine going back to strictly cig a likes? id hate my life. i started off with the disposables and now i use mech mods the change is fa nominal
 

zapped

Vaping Master
ECF Veteran
Verified Member
Nov 30, 2009
6,056
10,545
55
Richmond, Va...Right in Altria's back yard.
Also for the new guys a litle information on "tanks"

Clearomizers have been around since I started here but most people didnt fool with them because they leaked like sieves and were unreliable.

Then we got the Ego-T which holds liquid in a small plastic reservoir and dripped it onto a dripping attie via gravity

Shortly thereafter carto tanks were invented right here on these forums using plastic or glass test tubes and syringes coupled with cork or rubber grommets. People slotted or punched their own cartos with a dremel wheel or a hammer and nail and found that this method eliminates dry hits.

Its only been within the past year or so that the term tank has been used interchangeably for clearomizers like the Vision Nova and the Protank as well as RBA's and carto tanks.

Personally I prefer to call them carto tank, clearo tank and rbas as that speaks of the actual delivery method of the juice instead of the tank-like appearance shared by all and helps to avoid confusion.

Depending on the juice you use and the voltage, the performance and even flavor production of these devices can be drastically different from one another.
 
Last edited:

Rule62

Vaping Master
ECF Veteran
Verified Member
Oct 28, 2011
5,765
15,339
Melbourne, Florida
Also for the new guys a litle information on "tanks"

Clearomizers have been around since I started here but most people didnt fool with them because they leaked like sieves and were unreliable.

Then we got the Ego-T which holds liquid in a small plastic reservoir and dripped it onto a dripping attie via gravity

Shortly thereafter carto tanks were invented right here on these forums using plastic or glass test tubes and syringes coupled with cork or rubber grommets. People slotted or punched their own cartos with a dremel wheel or a hammer and nail and found that this method eliminates dry hits.

Its only been within the past year or so that the term tank has been used interchangeably for clearomizers like the Vision Nova and the Protank as well as RBA's and carto tanks.

Personally I prefer to call them carto tank, clearo tank and rbas as that speaks of the actual delivery method of the juice instead of the tank-like appearance shared by all and helps to avoid confusion.

Depending on the juice you use and the voltage, the performance and even flavor production of these devices can be drastically different from one another.

I still have a couple old 'redneck tanks' that I made from syringe tubes, in my desk drawer.
 

DancingHeretik

Dancing in the Chaos
ECF Veteran
Verified Member
Mar 20, 2011
8,837
62,105
San Antonio, TX
How about another blast from the past. The AltSmoke Silver Bullet was one of the first mass-produced mechanical mods. Made from aircraft-grade aluminum and machined to a then unknown quality, the SB has aged well over the passage of time being nearly as popular to this day as it was when first introduced in 1969. This was my very first mod along with the AltSmoke BB (14500 mechanical mod) two years ago. Both are workhorses which I still use to this day.

Watch Grimm Green review the SB (1969) as he uses an 18650 mod for the first time, and vaping at 6 volts (2 RCR123 stacked) for the very first time.



View attachment 337828View attachment 337829View attachment 337831View attachment 337830


Classic! To see him as a Silver Bullet virgin! But, the review was done on Nov. 11, 2009, not in 1969.

So funny to hear him wonder why anyone would want such an unnecessarily big battery. But, toward the end of the review, you can see him starting to fall for it. And, the love affair begins!
 

DancingHeretik

Dancing in the Chaos
ECF Veteran
Verified Member
Mar 20, 2011
8,837
62,105
San Antonio, TX

donnah

Vaping Master
ECF Veteran
Verified Member
Aug 22, 2010
4,470
4,463
Albemarle, North Carolina
mechs weren't all that popular until genesis attys hit the market. You needed a mech to be able to fire the low resistance that a genesis needed to "shine". Then all the highend mechs started coming out.. then the clones. Used to.. upgrading meant getting a regulated voltage device. Now I see people say they're "upgrading" to a mech.

I hunted Amazon for the materials to make my own carto tanks.
 
Status
Not open for further replies.

Users who are viewing this thread