Genesis Line - mini genesis

[BJ43]

One line ordered and paid for, now the wait begins.

 

[MXBNW]

So did it open for orders, I put my self on the list for (2)

Do we get an Email or do we need to go back to the Forum and check in.

 

[Finger82]

Yes payment instructions are on the other forum.

 

[MXBNW]

Yes payment instructions are on the other forum.

Looking for it now but can not find it.

 

[kcos]

Looking for it now but can not find it.

www.vaporwall.com • Login

 

[MXBNW]

www.vaporwall.com • Login

Thanks Ok another question

What is the Mini and Maxi

I wish I had more time to keep up with this stuff LOL

 

[Turbo]

Thanks Ok another question

What is the Mini and Maxi

I wish I had more time to keep up with this stuff LOL

This post should clear up the differences for you.

 

[MXBNW]

This post should clear up the differences for you.

Thanks .....

 

[cypresss]

Thanks Ok another question

What is the Mini and Maxi

I wish I had more time to keep up with this stuff LOL

Mini and Maxi

MX, here are a couple of videos and info on Mini and Maxi

 

[Vapeterry]

Lines paid for, sure am excited. @MX is your box full, tried to send PM??

 

[Turbo]

What is the procedure for wrapping the wick and posts for the Line using that tool?

Some were using one when we had our Hybrids, I never did. I think you simply feed the kanthal through it and use it to wrap around the posts. It creates a more secure wrap than fingers can give.

 

[Brazilleon]

Some were using one when we had our Hybrids, I never did. I think you simply feed the kanthal through it and use it to wrap around the posts. It creates a more secure wrap than fingers can give.

Hey Turbo, yeah one of those people was me. The wrapping on the hybrid and connection to the silver wires was particularly tricky. In the end I found my best setup was using a silver 1mm tube, someone else suggested, I'd loop the kanthal through the silver tube and back on itself, wind it tight to the tube and slide the tube over the neg silver wire connector and then make my coil, and use the wire wrapping tool to wrap the kanthal to the positive post.
I did have to modify the radio S tool as the diametre was smaller than the 1mm silver wire. I drilled 1.2mm or something to just the mod the tool. Worked pretty decent. gets a nice tight wrap with a few turns.
I did it by hand with the line and so far it's holding up pretty good. Not had to switch it or tamper with the business ends.

 

[mikescott]

Hi guys, I've just completed my first set up on the Genesis Line with 6 wraps of Kanthal and I'm getting 2.7 ohms which is great for the Provari. The coil itself is glowing but I'm not getting any glowing spots anywhere else which hopefully means it's not shorting. The first few minutes vaping were superb but then I started getting a burnt taste and dry spots ....it seems like it's not wicking fast enough. I'm using primarily VG juice I think (FSUSA's Hypnotic Mist). Just wondering what people do in this situation. Do I look at the wick or do I thin my juice with distilled water or vodka ?

 

[urquidezj]

I bought some fausa 100 vg rocking chair while my line was pulled apart, when I went to add it once rebuilt it didn't wick too well. So o am also interested I'm how to dilute it.

 

[gredie]

Do I look at the wick or do I thin my juice with distilled water or vodka ?

Both actions are an option. You could make a wick which is more loosen or take one not that fine like 325 mesh. Or you dilute your juice.

 

[mikescott]

Both actions are an option. You could make a wick which is more loosen or take one not that fine like 325 mesh. Or you dilute your juice.

Thanks Gredie, I will try and dilute my juice first.

 

[gredie]

Be aware that nic and taste will be diluted too. A few drops of water should be enough.

 

[oldsoldier]

This thread has been closed for posting. The new thread is now located here:
http://www.e-cigarette-forum.com/forum/modder-accessories-supplier-forum/250979-genesis-line.html