Genesis Line
- Thread starter shpaolin
- Start date
- th_trl_thread_readers 0
- Status
ok ,, just check the tracking , and its at my local post office, due to be deliver to me today,, yay!
Coolness.
Mine is....don't know. Can't be far away. If I haven't received it by the end of next week I will chase it down.
Only ordered mesh yesterday so could be a moot point anyway.
Sent from my MB860 using Tapatalk 2
Mine is....don't know. Can't be far away. If I haven't received it by the end of next week I will chase it down.
Only ordered mesh yesterday so could be a moot point anyway.
Sent from my MB860 using Tapatalk 2
I missed the postman so have to collect tomorrow.
Daft question time.
Somehow I managed to miss if The Line comes with mesh and kanthal or not ?
Daft question time.
Somehow I managed to miss if The Line comes with mesh and kanthal or not ?
Nope my was mesh and kanthal free. Ebay to the rescue.
Should have the mesh in a day or two and a bit longer for the kanthal.
Sent from my MB860 using Tapatalk 2
Should have the mesh in a day or two and a bit longer for the kanthal.
Sent from my MB860 using Tapatalk 2
well, after a couple of weeks of getting good vape from my V2line, today i picked it up to vape , and was getting e1 code on ProVari, cleaned coils, checked them for coils touching , and was ok, all looks good , but still getting E1 code, .. pulled of coil and pulled out wick, re- quenched the wick a few times, looks good, put on new coil, and still getting E1 code, must be a short somewhere in unit , how do i check for that, ...
Can this unit be easily taken apart/, i wonder if the insulator on silver wire for the possitive is worn and making contact to ground
Can this unit be easily taken apart/, i wonder if the insulator on silver wire for the possitive is worn and making contact to ground
Not certain of the etiquette but I would suggest posting the question were bought them.
Sent from my MB860 using Tapatalk 2
Sent from my MB860 using Tapatalk 2
i just noticed that the juice is bubbleing inside of tank when i hit the fire button,, now i know there is a short in the tank,
How can i fix this?
How can i fix this?
You can return it to Del for repair. There is a thread on vaporwall that will tell you how to do that.
thank you for the input, i got a mess. from Delboy, ,, i'm going to send it back..
I need help here..i gt problem with my line v2...the short pole rubber tube seems to be shorter than the longer pole after many times of replacing new coil and mesh..however recently it get short...when i open the top and see...the short pole seems to create small fire on it and glow spot when i activate it....is there a way i can do and troubleshoot it myself?Thank you
Sounds as though you are getting a hotspot between the coil and the shorter wire ?
Is that correct ?
Is that correct ?
From that photo it appears that there is no insulation (plastic) left where the short post goes into the body of the Line. That would definitely be a problem if contact is being made there.
Yes,,correct,theres no insulation left at the shorter post and it does contact the body of line...the hotspot is not on the coil and mesh,,but its at the bottom of the post near the centre whole of putting mesh there...Ist it about time for me to replace or throw it away?
No dont throw it away you need a bit of heat shrink tube to slide over the post and into the tank.
Pm Del to see what was used originally
Good Luck
Oh my godness! NO don't throw it away! It can be returned to Del for repairs or because of your location you may want to repair this yourself. As eyebrooke pointed out shrink tubing should do the trick if you can get it far enough down the post and into the body of the Line.
- Status
Similar threads
- Locked