Genisis LV and Box Kronos
- Thread starter Tai Pan
- Start date
- th_trl_thread_readers 0
- Status
Some asked - here are the answers.
How does a Genisis function?
The Genisis is a tank system with a normal 1,5 ml glass bottle as a tank. On top of the connector are two bolts for the voltage and a holder for the mesh.
The mesh goes via the middle part into the tank and guides liquid to the wire where this liquid is vaporised.Through 2 side bores of 1,5 mm in the middle part this vapor passes the bottle and flushes via the mouth pieces into the mouth of hte user. Now comes a very hard decision - into the lungs or not?
I am e.g. a pipe smoker and don't inhal. But that is specific from user to user.
This are images of the old version. The new one is optimized for stainless steel
- thin walls of 0,5 mm
- thread pitch 0,5 mm
- only 28 gramms
The bolts are fixed on an insert of stainless steel, which is glued into the bottom part than.
New images will follow.
How does a Genisis function?
The Genisis is a tank system with a normal 1,5 ml glass bottle as a tank. On top of the connector are two bolts for the voltage and a holder for the mesh.
The mesh goes via the middle part into the tank and guides liquid to the wire where this liquid is vaporised.Through 2 side bores of 1,5 mm in the middle part this vapor passes the bottle and flushes via the mouth pieces into the mouth of hte user. Now comes a very hard decision - into the lungs or not?
I am e.g. a pipe smoker and don't inhal. But that is specific from user to user.
This are images of the old version. The new one is optimized for stainless steel
- thin walls of 0,5 mm
- thread pitch 0,5 mm
- only 28 gramms
The bolts are fixed on an insert of stainless steel, which is glued into the bottom part than.
New images will follow.
Last edited:
Just ordered a Glv. I read the whole thread and still can't figure what the max volt on the box are (duh)can someone let me know??
Thanks
Bob
Thanks
Bob
Teach, shipping is position 7 in your invoice.
Think I'd better get my glasses checked! Thanks Uwe - I try not to bug you any more.
Thanks cos! Found this thread from a post you made in the classies. Wish I would have known you were going to sell your extra hybrid....I mutilated mine trying to turn it into a 510 cause I was tired of the switch problems.....oh well.
Should have listened to lorederos. Maybe i can copy the deminsions and have a new bottom turned. I've learned to make a different version, and now have my sights set on this one! For the price....you can't beat a complete set like this!
Has any one recieved one yet? I have been waiting for a review before I pulled the trigger.
please give us plenty of notice before you close it some of us may be forced to wait till the last moment due to funding issues...
and thanks again for doing all this i am sure it is a lot of work
and thanks again for doing all this i am sure it is a lot of work
No-one has recieved one of these from this co-op except for the creator of the mod and maybe a couple of others who got prototypes.
I can tell you that I have a few different Genisis mods both of my own creation and from other co-ops and I can honestly say there is nothing quite like the performance and configurability of Genisis on this forum. They can be confgured to give you as much or as little TH, flavor and vapor as you like and the taste is a cleaner than almost anything else that uses a wick to get juice to a coil.
That said, there is a learning curve. It's not so hard that anyone can't get through it and really enjoy their Genisis mod. Most get it right after a handful of mesh rolls and coil windings and shrotly thereafter it becomes second nature. Most people who have taken the time to learn the dos and don'ts of Genisis mods agree that it is their favorite vape and well worth the wait and effort needed to get the skills built up to work with them.
Typically the more accomplished modders are the ones that setup these co-ops and usually only when they have perfected the device and it is working to their satisfaction as a matter of pride, bragging rights or some of both
the quality on these things is usually very good to excellent...and always much better than things you can buy mass market. If you've heard of Genisis and want to try one, I think this is a very good design and I don't think you'll be disappointed at all with it.
No-one has recieved one of these from this co-op except for the creator of the mod and maybe a couple of others who got prototypes.
I can tell you that I have a few different Genisis mods both of my own creation and from other co-ops and I can honestly say there is nothing quite like the performance and configurability of Genisis on this forum. They can be confgured to give you as much or as little TH, flavor and vapor as you like and the taste is a cleaner than almost anything else that uses a wick to get juice to a coil.
That said, there is a learning curve. It's not so hard that anyone can't get through it and really enjoy their Genisis mod. Most get it right after a handful of mesh rolls and coil windings and shrotly thereafter it becomes second nature. Most people who have taken the time to learn the dos and don'ts of Genisis mods agree that it is their favorite vape and well worth the wait and effort needed to get the skills built up to work with them.
Typically the more accomplished modders are the ones that setup these co-ops and usually only when they have perfected the device and it is working to their satisfaction as a matter of pride, bragging rights or some of both
That sounds like music to my ears. One of the nicest compliments I've ever heard. I feel good
Yes, please let us know BEFORE you close. I want in, just have to wait a little while longer....by the end of this month.
on the go....with my Croatian Beast...Hybrid Mini!
Now we are making the fourth batch of the Genisis. When this one is finshed 780 Genisis are out.
The Genisis originally had been developed by Ichbines in aluminum.
We changed to stainless steel and manufactured two batches for the German forum with RCA connector only. Than we made a redesign to tighten the wall thickness and the threads and to skip bolts in stewalin an use an stainless steel insert instead.
The series III is in preparation now, the metall parts are here and we are assembling the bottom parts, and will deliver in about three weeks.
You are waiting for series IV which is in production. Hopefully we will get this one out by end of August.
If there will be a series V depends on the interest. It does not look like in the moment.
Uwe
Last edited:
- Status
