Getting error code 0 with IBTanked on Provari 2.5

[MontanaDoc]

Been using Kanger Protank II for ever after getting 1st Provari. Recently decided to try the IBTanked. Initially it worked wonderfully. Then after approximately 10th refill I started getting error code 0. Figured it was the pin not connecting, so replaced with new atty. No change. Tried on the Provari mini (also used with this in the past), another 0. I have like 20 replacement attys and am not happy.

I would appreciate any suggestions.

Right now, using the Protanks.

I plan on trying rebuildables, looking at that Russian 92 (91?) but not sure if this is usable on the Provari

 

[xtwosm0kesx]

I'm unable to find any mention of an "E0", according to Provape's site the codes run E1-8?

Sounds like a possible cartomizer issue though.

Keep in mind the IBTanked is essentially just a 'juice tank', in that it sits around the cartomizer and shouldn't directly influence its performance(i.e. cause the code), its just there to feed the carto juice.

I would try a new carto, and see if you still get the error code.

Best of luck!

 

[MontanaDoc]

I'm unable to find any mention of an "E0", according to Provape's site the codes run E1-8?

Sounds like a possible cartomizer issue though.

Keep in mind the IBTanked is essentially just a 'juice tank', in that it sits around the cartomizer and shouldn't directly influence its performance(i.e. cause the code), its just there to feed the carto juice.

I would try a new carto, and see if you still get the error code.

Best of luck!

Yes, I understand that, thank you. I wasn't sure what specific carto to name and assumed they had a standard that came with the tanks. As mentioned, I have actually replaced the carto three times and keep getting E0 and no firing. Even tried the original carto that I used initially for a week or so before this started, same result.

 

[Topwater Elvis]

You can use any 510 threaded delivery device on the provari.

E0 isn't a known error code, either ask in the Provape sub forum or contact them directly.

Are you talking about having problems with prostank attys/ heads or cartomizers.

 

[InTheShade]

Been using Kanger Protank II for ever after getting 1st Provari. Recently decided to try the IBTanked. Initially it worked wonderfully. Then after approximately 10th refill I started getting error code 0. Figured it was the pin not connecting, so replaced with new atty. No change. Tried on the Provari mini (also used with this in the past), another 0. I have like 20 replacement attys and am not happy.

I would appreciate any suggestions.

Right now, using the Protanks.

I plan on trying rebuildables, looking at that Russian 92 (91?) but not sure if this is usable on the Provari

So your protanks are working fine on the Provari?

That is very strange. Like others I haven't seen or heard of E-0 from the Provari. I would contact Provape directly.

 

[LMS62]

Been using Kanger Protank II for ever after getting 1st Provari. Recently decided to try the IBTanked. Initially it worked wonderfully. Then after approximately 10th refill I started getting error code 0. Figured it was the pin not connecting, so replaced with new atty. No change. Tried on the Provari mini (also used with this in the past), another 0. I have like 20 replacement attys and am not happy.

I would appreciate any suggestions.

Right now, using the Protanks.

I plan on trying rebuildables, looking at that Russian 92 (91?) but not sure if this is usable on the Provari

I have a Russian91% on a Provari and it works perfectly.

 

[JohnnyBGoode]

Error 0??? I would toss the provari...

 

[stevegmu]

Never heard of E0, but try taking out the battery and putting it back in...