Good news Evic Mini Users! Firmware 1.2 Upgrade to 75W !!!!

[ezjayy]

I always end up with the cotton in 2 pieces after 1 day of use....it's just frustrating...tried vertical coil build, failed, try pancaking now...seems a bit better...but I;m not sure how it's going to hold up...each time I have to go through 3 to 5 coils to get it just ok..before it break the next day

Eh like serious onli brudder. What tank you use? Your coil? Resistance?

 

[sibehsteamsiah]

!!! stainless steel mode. time to put those crown coils to good use

 

[anotherchap]

Eh like serious onli brudder. What tank you use? Your coil? Resistance?

Subtank mini and 0.5 ~ 0.6 ohm

 

[isux]

Subtank mini and 0.5 ~ 0.6 ohm

I used to have these issues when i started out. It all boils down to your wicking technique. Not say that we are all damn good, but it takes some effort to at least learn and be proficient with the wicking. Some pointers are:
1. Remove the top and bottom layer of the cotton pad (these are the stiff ones)
2. Ensure that the wicking roll is not too tight between the coils (they need space to absorb). Too tight will end up just the coil burning through the packed cotton within the coil.
3. Feel free to loosen the cotton by stretching them slightly

Youtube has 1001 ways on how to wick.
@Pouf once mentioned before (and I have to say ... AGAIN for the nth time).. you may refer to the tutorial below:

 

[ezjayy]

I used to have these issues when i started out. It all boils down to your wicking technique. Not say that we are all damn good, but it takes some effort to at least learn and be proficient with the wicking. Some pointers are:
1. Remove the top and bottom layer of the cotton pad (these are the stiff ones)
2. Ensure that the wicking roll is not too tight between the coils (they need space to absorb). Too tight will end up just the coil burning through the packed cotton within the coil.
3. Feel free to loosen the cotton by stretching them slightly

Youtube has 1001 ways on how to wick.
@Pouf once mentioned before (and I have to say ... AGAIN for the nth time).. you may refer to the tutorial below:

Ah this one advice vely the good. Follow it and thy shalt find the Holy Grail.

 

[anotherchap]

I used to have these issues when i started out. It all boils down to your wicking technique. Not say that we are all damn good, but it takes some effort to at least learn and be proficient with the wicking. Some pointers are:
1. Remove the top and bottom layer of the cotton pad (these are the stiff ones)
2. Ensure that the wicking roll is not too tight between the coils (they need space to absorb). Too tight will end up just the coil burning through the packed cotton within the coil.
3. Feel free to loosen the cotton by stretching them slightly

Youtube has 1001 ways on how to wick.
@Pouf once mentioned before (and I have to say ... AGAIN for the nth time).. you may refer to the tutorial below:

Thank you! I haven't thought about peeling the outer layer off! I am going to give it a go!

 

[cloudysheep]

I used to have these issues when i started out. It all boils down to your wicking technique. Not say that we are all damn good, but it takes some effort to at least learn and be proficient with the wicking. Some pointers are:
1. Remove the top and bottom layer of the cotton pad (these are the stiff ones)
2. Ensure that the wicking roll is not too tight between the coils (they need space to absorb). Too tight will end up just the coil burning through the packed cotton within the coil.
3. Feel free to loosen the cotton by stretching them slightly

Youtube has 1001 ways on how to wick.
@Pouf once mentioned before (and I have to say ... AGAIN for the nth time).. you may refer to the tutorial below:

I kinda use the Scottish method if I'm using kendo, only thing is that I'll roll it tighter, then after setting it up, I sort of pancake it out at the ends... I guess it should be called a Scottish pancake then haha

 

[cloudysheep]

Subtank mini and 0.5 ~ 0.6 ohm

I'll prob do a stm wicking tut on how I do it for horizontal and vertical if I can over there weekend or sth...

 

[cloudysheep]

Thank you! I haven't thought about peeling the outer layer off! I am going to give it a go!

For stm, if I'm doing a horizontal, I'll just peel one layer off and the other stiffer side I'll use it as a barrier against the wicking hole, yes it's ever so slightly stiffer and cos of that I think it kinda helps to stop the flooding that may occur..

 

[anotherchap]

Thank you! I haven't thought about peeling the outer layer off! I am going to give it a go!

Just did a re-wick, glad i opened up my coil as it was already burnt! Now installing the scottish roll, hopefully I did it right and I'll see what happens!

 

[ezjayy]

Just did a re-wick, glad i opened up my coil as it was already burnt! Now installing the scottish roll, hopefully I did it right and I'll see what happens!

Scottish roll, pancake roll, rolling in the deep..just do eet!

 

[isux]

Scottish roll, pancake roll, rolling in the deep..just do eet!

I'll opt for tissue prata roll with condensed milk. Yum yum

 

[ezjayy]

I'll opt for tissue prata roll with condensed milk. Yum yum

Damn now im hungry.

 

[cloudysheep]

Damn now im hungry.

Come.. Go for prata and teh ai mai?

 

[isux]

Come.. Go for prata and teh ai mai?

bo jio...

 

[ezjayy]

bo jio...

Come come..i jio Darkwing Duck aka @Comrade Vape oso..dont want him stuck with pu*sycat all day.

 

[isux]

Come come..i jio Darkwing Duck aka @Comrade Vape oso..dont want him stuck with pu*sycat all day.

i think it's his Persian carpet...

 

[Epic_Sinner]

Wanna jio jio can don't start blowing clouds in public ah.

 

[ezjayy]

Eh no lah no lahhhh.. i inspired by @Comrade Vape 's Batman 'Creature of the Night' speech in the other thread.

Anyways pockets ain't deep for Gahmen donations. Heheh.

 

[ezjayy]

Ehh damn swee.. got SS temp control pulak tu..