Good RBA for Stainless Steel Vamo?

[ArmyByrd]

Title asks it all. I'd like a nice rba to sit atop my Vamo that I just bought. Something that sits flush on top. Smaller diameter than the Vamo. Preferably a matching stainless steel, also. Pictures would be wonderful!

Thank you!

 

[Kanj.nguyen]

AGA-T+. Basically looks like it was born to be the VAMO's companion.

 

[ArmyByrd]

AGA-T+. Basically looks like it was born to be the VAMO's companion.

Where is the best place to purchase this? I'd definitely prefer an atomizer/mesh/wick combo.

Thanks again!

 

[Kanj.nguyen]

Check out mountain oak vapors. $25 i think.

 

[DiegoVol]

I Just picked up a AGA-T2 from Clouds of Vapor. Lots of places seem to be out of stock on them at the moment. It looks amazing on my Silver Bullet. Excellent vape as well. I drilled the vent hole out to my preferred size.

 

[ArmyByrd]

I was literally on their site and switched tabs and saw your reply. Would you recommend 400 mesh or 325? Also, 28 gauge or 30?

 

[Red_Bird]

AGA T2
.......

Same as AGA T+ but a pyrex glass tank not a plastic one.

#500 ss mesh and 30 gauge kanthal is thick enough for a new guy wrapping coil. 28 is overkill and best for more experienced hands.

 

[gregzbobo]

I have only used #400 mesh in my AGA-T2, but from what I understand #325 is for VG heavy or really thick juices, #500 is for thin juices, and #400 is middle ground.

 

[qorax]

With Smok-RSST

 

[ArmyByrd]

So far I've got the AGA T+ Pyrex Atomizer, #400 SS mesh, a SS drip tip, and some 32 gauge kanthal in my shopping cart over at Mountain Oak Vapors. They only offer #325 and #400 SS mesh. I think I have everything I want, yeah?

 

[Kanj.nguyen]

What mesh to use is a matter that is really up for debate. It depends pretty much entirely on what wick configuration you make. If you are talking about just wicking power, 500 is the best regardless of juice. It gets complicated because you will want to tilt while vaping. It gets quite technical and i wont confuse a newbie any further with it. But i suggest picking up 500 instead of 400; it is more versatile. I use 500 in all my wicks.

 

[ArmyByrd]

I use 50/50 PG/VG so #400 mesh will be good, yeah?

 

[Kanj.nguyen]

With Smok-RSST

Qorax is that a new tank for the RSST or just the color of your juice? I have seen a black/ smoky colored tank for the RSST but cant seem to find any vendor that carries it.

 

[DiegoVol]

You can buy 25 feet of Kanthal off ebay for the same price of 15 feet.

 

[Red_Bird]

ya on the #400, but you will curse a lot makin coils if u buy 28 gauge kanthal to start with.



I got 100 feet of 30 gauge kanthal from Temco DELIVERED for $5.96

 

[Ryedan]

#400 will do it, but 500 will wick better.

 

[ArmyByrd]

With Smok-RSST

That looks nice... hmmmmm..

 

[DiegoVol]

What mesh to use is a matter that is really up for debate. It depends pretty much entirely on what wick configuration you make. If you are talking about just wicking power, 500 is the best regardless of juice. It gets complicated because you will want to tilt while vaping. It gets quite technical and i wont confuse a newbie any further with it. But i suggest picking up 500 instead of 400; it is more versatile. I use 500 in all my wicks.

Very true. I'm using a 400 Mesh at the moment and I was using 500. I much prefer the 500 over it.

 

[Kanj.nguyen]

I have used as low as 200 on a special configuration and it works amazingly well. Really up to you to fine-tune your setup to fit your own habit and preference. But thats the beauty of RBAs isnt it?

 

[DiegoVol]

ya on the #400, but you will curse a lot makin coils if u buy 28 gauge kanthal to start with.



I got 100 feet of 30 gauge kanthal from Temco DELIVERED for $5.96

Temco is the way to go on Ebay. I have ordered twice from them. I think price wise it works out to roughly .03 cents a foot on both my orders from them.