Griffin Tank

[zamster999]

Got gotten my new Griffin tank and i'm not really getting much of a positive experience.
I'm running 24GA Kanthal, 5 warps 0.2ohm, firing at 28watts.
This setup is identical to my TFV4 and uwell crown.
Both works fine but not for griffin.
Very bad spitbacks, leakage and bad smokes.

Any advise?

 

[avex30]

It is somewhat similar to Obs

Leakage is due to your cotton too thin.
Spitback issue Should be related to your coil.

24 ga 5 wrap dual coil? Getting 2 ohm? What is your interNAL diameter?

Cause I use 24 ga 6 wrap internal I get about 3~4 ohms. And I got bad taste coming I got to rip it out use s syring to suck the juices n rip out the coil.

change 26 ga 5 n half wraps got about 2.7 ohms interNAL diameter 2.5 I using coilmaster 25 rig. Fire at 35 watts no Spitback.

 

[cloudsclouds]

be aware.... there are 1:1 clones of the griffin floating ard the marketplace and also in the shops.... no real way of telling them apart.... had a friend who held both the clone and original in his hands and cannot tell them apart

mine works beautifully btw....

 

[zamster999]

i just changed to clapton, diameter 3.0, 26GA, 7 warps 0.52ohm, firing at 35watts. a little spitbacks but still bad smokes. quite tough to manage with the cotton for griffin, especially when i used to play with tfv4 and uwell crown. the cotton management is way different.

 

[charles8888]

Try using scottish roll on clapton. Have to trim the end thinner to fit the juice hole.

 

[Karstine]

@zamster999

Trying going 40 watts. Clapton has slow ramp up time.

Your 0.2 coil is going to produce less vapor. You need 88 watts to get around 4.2v.

Play around with the wattage man. Experiment is your best friend

 

[zamster999]

@zamster999

Trying going 40 watts. Clapton has slow ramp up time.

Your 0.2 coil is going to produce less vapor. You need 88 watts to get around 4.2v.

Play around with the wattage man. Experiment is your best friend

Thanks! I'm firing at 50watts RN, 26GA, 7warps clapton, 0.44ohm, Using the scottish roll method. Had a very bad leakage in the beginning but it's alright now. Having a little spitback once in awhile. Not sure why the bad leakage.

 

[Karstine]

Thanks! I'm firing at 50watts RN, 26GA, 7warps clapton, 0.44ohm, Using the scottish roll method. Had a very bad leakage in the beginning but it's alright now. Having a little spitback once in awhile. Not sure why the bad leakage.

not enough cotton

 

[taps41]

Did u check and make sure ur cotton is not over the air holes?

Sent from my Redmi Note 2 using Tapatalk

 

[Loylipop]

24G Kanthal, Dual 8wraps on 2.5mm 3.5Ohms Firing at 42Ws on my IPV3LI

Chain vaping massive clouds and vapor all day thou I have to change coils and cotton every 2-3 days cause it burns.

 

[Loylipop]

Personally, my trick to the leaking issues is to close the juice holes and the air holes whenever I refill the tank. I only start opening the holes and vaping after putting the cover on and letting it rest for 5-10Seconds. And the cotton don't have to put through the hole, just let it rest on top of it enough to cover 90% of the hole can already.
BEST.RTA.EVER

 

[avex30]

Bro is0.35 or 3.5?

24G Kanthal, Dual 8wraps on 2.5mm 3.5Ohms Firing at 42Ws on my IPV3LI

Chain vaping massive clouds and vapor all day thou I have to change coils and cotton every 2-3 days cause it burns.

 

[Loylipop]

Bro is0.35 or 3.5?

OOOPPS .35 PAISEH PAISEH HAHAHAAH

 

[zamster999]

Recently i've done a rewick and the same problem arise again. But it's weird cause after i did a rewick, and fill up the tank, it will have a big leakage, and after that it will resolve by itself.

 

[Karstine]

Recently i've done a rewick and the same problem arise again. But it's weird cause after i did a rewick, and fill up the tank, it will have a big leakage, and after that it will resolve by itself.

If you find that you are leaking at the start of refill. Probably problem with vacuum pressure in the tank . One tank known for leaking at refill is the bellus.

But having use the bellus for quite a while, I realised that having just enough cotton (more than you think) in bellus actually stops the leaking at the refill.

Just play around with the cotton man. I wasted half a bottle of juice when I first got into vaping. I still waste some amount of juice if I'm building in a tank that I'm not used to.

 

[zamster999]

-snip-.

thanks for the kind advise! but i guess i'll just get tanks with RDA in the future. RTDA seems like another world i don wanna venture into lol.

 

[cloudsclouds]

Do the Bellus trick to refilling, i think there's a tutorial for the Bellus done sometime back search for it

 

[crisisady]

I have tfv4 which is well known for leaking. So what I did was to make sure that I don't fill the juice to the brim. Just fill it to about half way.

BTW, how's the flavour on Griffin? I'm considering to get it.

 

[avex30]

OOOPPS .35 PAISEH PAISEH HAHAHAAH

hmm griffin n obs should be easy to Build and wick could a your tank defective. I just realise my so call authentic tvf4 mini leakage problem is due to coiling base

LOL 3.5 abit scary

 

[Trexer]

The top cap of my bnib griffin cannot open so right now i do not know how to fill it up with juice