HCigar VT200
- Thread starter MegaVap
- Start date
- th_trl_thread_readers 0
- Status
Well after ordering a bunch of battery of hobbyking i can safely say that its imposible to have a 1300mah battery that small!
i found a nice high C battery that tightly fit in the case .. some propblem fiting it with the xt30 connector .. had to remove battery wrap.
https://www.hobbyking.com/hobbyking...ch_A_SPEC_G2_1000mah_3S_60_90C_Lipo_Pack.html
Specs:
Capacity: 1000mAh
Voltage: 3S1P / 3 Cell / 11.1V
Discharge: 60C Constant / 90C Burst
Weight: 96g (including wire, plug & case)
Dimensions: 70x34x19mm
Balance Plug: JST-XH
Discharge Plug: XT60
set my dna200 mod to 11.1 WH and it work all day ! so i am happy with it like this!
i found a nice high C battery that tightly fit in the case .. some propblem fiting it with the xt30 connector .. had to remove battery wrap.
https://www.hobbyking.com/hobbyking...ch_A_SPEC_G2_1000mah_3S_60_90C_Lipo_Pack.html
Specs:
Capacity: 1000mAh
Voltage: 3S1P / 3 Cell / 11.1V
Discharge: 60C Constant / 90C Burst
Weight: 96g (including wire, plug & case)
Dimensions: 70x34x19mm
Balance Plug: JST-XH
Discharge Plug: XT60
set my dna200 mod to 11.1 WH and it work all day ! so i am happy with it like this!
My hcigar VT200 Failed yesterday after two weeks of use
, up until the failure I was very happy with the device.
, up until the failure I was very happy with the device.Sorry to hear it. Your vendor should swap it out without issue, you can contact manufacturer directly should it be necessary. If they fail you Evolv warrants the board for a year, but I think you'll need to do the replacement yourself with the Evolv option.My Hcigar VT200 Failed yesterday after two weeks of use
Always a few bad ones ...... even with a quality board like the 200.
I am the vendor, TBH even though I was a bit upset that my Hcigar VT200 died on me after only a couple of weeks, I'm glad it happened to me and not one of my customers.
I did try that Escribe does not even detect the VT200, windows does not detect the device has been connected with the usb.I don't think that your VT200 is dead. Try to revive it with EScribe
Sounds like chip. If so.. that will be first example of DNA200 fail ive heard.
Did ya try manually updating firmware?
Connect device, start EScribe and then click
Tools/Update Firmware
As I have said before the software does not see the device, and if the software does not see the device how can you update it?
Im not sure if dna200 can work without battery (just usb plug in). If not, do u have spare lipo battery?
Manual update can force update when device is not recognized and install firmware anyway.
If this doesn't un-brick your device than it is something else than corrupted firmware causing your issue.
Last edited:
All I did was change the tank because I wanted to change flavor, what should have happened was new coil, but instead the screen just flashed and then went dead, the same tank was on the device a few hours earlier and was working fine without any issues. Something as simple as changing a tank should not cause any device to fail.
Mine won't respond to anything. I've tried using Escibe and its not being recognized at all. Just completely dead.
Contact you vendor, they should not have any problem replacing it for you.
Quite a few, yet a small percentage of the earlier boards failed due to a blown fuse at the main power connector from battery + pad, but in these instances the board would usually light up screen (but not vape) and connect to Escribe when a usb cable was connected. Also heard of a few screens dimming out & failing.
I had a Hana V200 that would not update firmware at all that Evolv sent a replacement board for.
Do you think it's lasting longer than stock battery
- Status
