Help with Cisco Spec 1.8 Atomizer

[Petedacook]

I've been trying to find information on this Cisco Spec atomizer for days and I have had no luck. I even made a post at Reddit asking , but that didn't help either. I have used cartomizers since I started vaping 8 weeks ago, except for the eGo T I tried which lasted a tank of juice.

I have two questions I cannot find answers to.

1. How do I get the plastic off the top so I can insert a drip tip? This atomizer came with a plastic case around it. The tip of the case, where the drip tip would normally go, has a piece of plastic covering it, and a piece of plastic behind it with a small hole for air to pass. This is just like the white disc that comes in a cartomizer in the drip tip end, normally easy top remove. Is there a part I can buy that will allow me to add a drip tip?

2. How do I switch between juices? Do i just vape one juice until it begins to dry, then add the new juice? How do i prevent falvors from mingling together?


I really have no clue about atomizers. Please feel free to volunteer any information about atomizers.

 

[bilboda]

I'm not seeing a Cisco spec atomizer in that link that you posted. If that link is correct there is a tip at the bottom of the page.

 

[Petedacook]

Fixed the link. It is not a clearomizer I am asking about. Although I am ordering one of those.

 

[bilboda]

Use a paper clip. insert in hole and pry it out. Any of the tips on their site for 510 should work. The various clearomizers are a nice concept but often disappoint due to wicking and sometimes leaking. The atomizer you selected is one of the better ones. Look around for a bottom feeder to use with it or just drip in it.

 

[kwalka]

I have a bunch of these...
1. I remove the whole plastic insert and toss it, put a drip tip directly on the atty.
2. I pretty much drip exclusively, so I just switch without even blowing out the atty. The first time you drip a new flavor the 2 flavors will be mixed. By the second round of dripping you are getting all of the new flavor. If you dont want to mix on the first round blow out the atty. Always blow from the threaded end, never into the top of the atty.
Also if your going to get into dripping next time you buy try the bridgeless attys, and once you get the hang of it do yourself a favor and spend the extra $ on an HH 357. They are well worth the extra $, just make sure you follow the instructions on the site.

 

[Petedacook]

Thank you all for the responses.]

I have a bunch of these...
1. I remove the whole plastic insert and toss it, put a drip tip directly on the atty.

This is the part that is killing me......the plastic insert is not actually a plastic insert, it is molded plastic with the rest of the cover. It has a small groove around the edge to make it appear, at a glance, that it is not one contiguious piece, but it is. Behind that little piece of plastic at ther top is a little white disc. The disc is floating around in the tube, so it is not a contiguious piece with the cover.

Maybe they just began sending these? I am trying to get pictures or a video to upload. I am just going to cut it out as best I can.

Down the road I am going to get the 357. Since this is my first atty (not including the one eGot T I had), I wanted to play it safe.........like what Kwalka said....once I get the hang of it.

 

[Petedacook]

I got a decent looking pic. This is the atty on the battery standing up.
http://i.imgur.com/K0bzd.jpg

it looks a bit banged up because I was trying to pry, what would normally be, the little plastic insert from the top, but it is part of the casing.

 

[Petedacook]

No one knows anything about this anomalie?

 

[Harley]

Ok,, It looks to me that you have a 306, NOT a 510... If you grab the black case while the atty is screwed into your mod the whole plastic piece will come off, THEN you will need a 306 drip tip... NOT a 510....

Look at the link below, I think this is what you have,,,,,,,

http://www.avidvaper.com/cisco-hr306-atomizer-drip-tip-special/

 

[Petedacook]

That is exactly what it is. Many thanks, Harley.



I checked my order and it is the 306 1.8 ohm. I have no idea how I ended up ordering the wrong thing.


Now I need to decide if I should get the 306 drip tip, or a 510 atty, or just use what I have.

 

[kwalka]

I would get a drip tip if I was you. Have you ever trie a 306? They wont take it back so it seems like your only choice. You may find out you like 306s better.

 

[Petedacook]

This is my first atty.

What is the difference between 306 and 510, beside the obvious size difference?

 

[kwalka]

306 is much hotter, and the air flow is different because a 510 coil is exposed to more air. So IMO there is more TH on a 306 vs a 510. I use both all the time. Right now I have 1 of each on 2 diff box mods. I am by no means an expert I have only recently switched to all attys and I couldn't be happier. I will never buy another carto. I'm sure someone who can better explain the difference will chime in.

 

[Petedacook]

I think I am quitting carts as well.

Why did you switch to all attys?

 

[kwalka]

Because nobody has ever really tasted their juice until they have dripped it on a good atty. This is not my quote I'm just repeating what has been said by many b4 me.