My evod is gurgling and leaking. I have tried everything. All the tips. Could the top part that holds the liquid be damaged? 
Help with Evod ASAP
- Thread starter Tgibbon45
- Start date
- th_trl_thread_readers 0
- Status
Check and make sure the coil is screwed tight...and make sure there is no liquid down the center tube...just my 2 cents
make sure the 2 o rings are in place and all is finger tight- if so already- try a new coil
Ah sorry, when you unscrew the bottom polished ring there is an 1/8 inch tube sticking up that is replaceable. Just unscrew that assembly and replace assuming you have another. That houses the coil and wick that creates the vapor.
How To: Filling The Evod And Replacing The Coil Heads - YouTube
But i see you already did that
How To: Filling The Evod And Replacing The Coil Heads - YouTube
But i see you already did that
Last edited:
Hey there.... Tip the tank upside down and blow (from the base to the tip) into a paper towel or kleenex. Make sure there's no juice in the air shaft. Keep the tank on its tip. Make sure there's no juice where the tank connects to the battery (fold a corner of a paper towel/kleenex or take a cotton swab and make sure that's dry - just be careful not to push too hard, as you could push down the pin of the battery). Make sure your base is snug to the tank (don't overtighten.) Try reassembling - don't overtighten the tank to the battery.
You might be trying to pull too hard. Slow, easy draws. Don't try to suck your battery into your lungs
:edit: you don't mention what kind of device - is it vv/vw? If so, is your voltage or wattage set appropriately. if you're too cool, you can't heat the juice up as well to vape. If too high, you'll burn
You might be trying to pull too hard. Slow, easy draws. Don't try to suck your battery into your lungs
:edit: you don't mention what kind of device - is it vv/vw? If so, is your voltage or wattage set appropriately. if you're too cool, you can't heat the juice up as well to vape. If too high, you'll burn
Last edited:
I'm thinking that may be it. Looks like I'm SOL for tonight. I hope the hubby lives through the night. Haha.
I may just get another kit all together instead of trying to figure out what part is not working. I haven't had this issue since I got it. It also seems to be going through a lot of coils. But that could just be me not knowing when I really need to replace it. I've got plenty of coils to rebuild thought if I decide to stay with the EVOD. As far as it being a vv/vw I have no idea what that means.
What vv/vw means:
Variable Voltage (VV): Variable Voltage lets you control how many volts your device will produce. Usually with a variable voltage e-cig, youll be able to dial in the voltage by a click of a button or sequence. If you have a 2.0 ohm coil you can set the voltage at 4 volts. It's your ohms x 2.
Variable Wattage (VW): Variable Wattage lets you control how many watts your device will produce. This will allow you to set it and forget it, no matter what atomizer or cartomizer you use with the device.
I had a vv but it fell and broke. So now I just use the original one that came with it. It isn't adjustable.
When i was using them I too blew on them but another thing I always did was held a napking over the mouth and sort of shook it several times like a old timey thermometer. A bit of liquid would be on the napkin then I would screw it on (also use a q-tip and make sure the battery is clean and liquid free) and that ended my problems with gurgling. Another thing is to take the flavor wick off the top. When I started building them (which they are very easy to do) I left off the flavor wick and found I liked then even more. Hope this made sense and helps some. Good luck to ya.
- Status
Similar threads
- Locked
