Hey from South Central KY

[Ginnyb]

So I am new to forum, but have been vaping several months. Would like some advice re: EVOD clearomizers. Was reading everywhere how wonderful they were and recommendations both here and other sites. Well, bought my first one and it immediately leaked every where. So, spent a little more money and bought a second one, thinking okay one is slightly defective. It also leaked. Then I tried a G 50. It leaked. Think I am done with bottom fill, bottom coil. Have watched several You Tube videos and have tried everything I can think of short of totally rebuilding and it is not worth all that except I do have almost $50 bucks invested. Have tried screwing real tight, blowing them out, screwing tight, tight, cleaning threads on both batt and clearo. So what does one do to use these bottom coil things?

 

[Steam Turbine]

First of all: Welcome to ECF!

Secondly:

Sounds like user error to me!

Where do they leak from?

 

[daleron]

Wow, rough start! I don't know
Have you considered trying a pro-tank?
Anyway, this will bump you back up in the stream so maybe somebody else will answer
I didn't have any problem with mine

 

[Thunderball]

Welcome to the Forums.......and the journey begins......

I dont have the patience with the evod....everything has to be "just right"... Others will figure it out for you. Welcome !!

 

[Ginnyb]

They either leak where the tank screws back on to the coil, they squirt juice in my mouth, and they leak on the bottom where they sit on the batt. I agree, it could be user error (my fault) but what am I doing wrong. Have v2 love and have taken it apart, put in new wicks and put back and no prob. Love the T2 and of course CE 4 and 5..

First of all: Welcome to ECF!

Secondly:

Sounds like user error to me!

Where do they leak from?

 

[Baditude]

I agree, is probably user error. I have a few of the Evods and not had a issue with them leaking. Occassionally one will just stop working. I've tried increasing the voltage up over 5 volts and done some pulse fires which seems to get them working again. Since this works, I thinking that the coils are getting gunked with accumulated dried juice and burning it off seems to work so far.

I can't suggest any fixes for the OP. He's watched demo videos and knows not to get juice in the center hole. Blows out the air hole. Checks that all parts fit snug. I'm stumped.

It shouldn't matter, but are the juices that you use particularly thin, like all PG?

 

[MJ12]

Have tried screwing real tight, blowing them out, screwing tight, tight, cleaning threads on both batt and clearo.

Overtightening may be your problem, at least that's what I experienced with my eGo-T and Vision Victory clearo. I was told to screw the batt on just finger tight and no more.

 

[Hill]

Yea I've had problems with the EVOD as well Although I think mine may be counterfeit.
I use the Vision ViVi Novas now they seem to work much better for me.
I have a couple Protanks that I use every now and again but the ViVis are my Workhorses so to speak.

 

[Ginnyb]

Thanks everyone.

 

[ghola1was]

I haven't had any issues with my Evods, sorry to hear about your difficulties.

Please inspect the white o-ring between the coil base and the Evod for damage. Also, do not over tighten those pieces.

Next, locate the white-ish grommet on the center post of your coil. Try putting another one of those grommets upside down onto that post so that you have two grommets. When you screw the Evod back on it the inside tube should "nest" into that grommet providing a better seal.

 

[Ginnyb]

Just wanted to thank you again and let you know I got a ViVi Nova after your response, have been using for a couple days now and really like.....it and the T2 are my faves.