Say what you want about the Ithaka, it is built like an M1 Abrams. (I would have said "tank", but, you know)
High-End Mechanicals Chat, Tips, and Pics
- Thread starter b0redagain
- Start date
- th_trl_thread_readers 0
- Status
Nemesis Mixed Matte #6105 + Trident V2 rda #1045
Nemesis Kalafan #4542 + Trident RDA #3319
...I must take back my doubts voiced earlier about the QC on the Trident V2....toothbrush and soap to the posts and screws fixed every issue I had with this dripper. I highly recommend this fantastic dripper to anyone, and especially to those that had the original Trident. It is a major improvement in style, overall form, chamber construction, all vapor related characteristics follow these improvements. Excellent product!
Nemesis Kalafan #4542 + Trident RDA #3319
...I must take back my doubts voiced earlier about the QC on the Trident V2....toothbrush and soap to the posts and screws fixed every issue I had with this dripper. I highly recommend this fantastic dripper to anyone, and especially to those that had the original Trident. It is a major improvement in style, overall form, chamber construction, all vapor related characteristics follow these improvements. Excellent product!
Last edited:
A major style upgrade if you ask me. I dont like the original trident looks, but the Trident 2 really catches my eye
Too funny, I can't believe you just posted this picture...... Literally an hour ago I put my Latina on my Copperhead for the first time and filled up the tank for my evening vape.
Last edited:
Last edited:
Trying to figure out multiple pics with tapatalk. Not sure so here's the other pic.
Ken
Sent from my iPhone using Tapatalk
Ken
Sent from my iPhone using Tapatalk
very nice...that's one of the few things out there that im considering for 2014 seriously....Trying to figure out multiple pics with tapatalk. Not sure so here's the other pic.
Ken
Sent from my iPhone using Tapatalk
lemme know what you think.....? a short review?
especially interested in juice control/airflow on the aqua? switch quality on the mod?
thx and enjoy!
Atty setup is very similar to KF. I'm sure u've seen some setup vids. I used .5 flat wire and it wasn't the easiest to get under the screws. I tried to set it up similar to my KF builds so I could draw a comparison. Folded over 3 mil silica and was shooting for 1 ohm total, got close with 1.2. Filled up, turned upside down to finalize tightening of top cap but still got some gurgling. Blew it out upside down and no flooding since. So far it's a very similar vape to me as the KF. I don't taste a significant diff, flavor is very good though. Def blows some clouds. As a dual coil I imagine this thing will go thru juice fast so the clear tank will be my next buy.
The Origin is nice and I like the look. Couple things I found though I wasn't fond of. There is a beauty ring on the switch just above the locking ring. That ring is held in place by an oring. When locking the switch that ring will move and at times be crooked. Again it's held in place by an oring, I may look for a bit larger oring to hold it in place better. No big just wasn't excited by it. The other is u can adjust the firing pin/screw in the switch. I believe is to make the switch throw shorter..I think. So when locking the switch that adjustment screw will move as I'm turning the locking ring. It can then move the pin out of reach of the bottom of the batt, again not end of the world but not fond of it. It may be user error as today was first day with both. It does look the cats meow as a hybrid in 490 mode.
Ken
edit: haven't tried juice control, haven't had a dry hit or even a hint towards it. I saw some vids where they weren't even using it. So for now I keep juice control closed as it seemed to wick fine. Air control at wide open is a tad more open then the KF lite and I think about the same as 3.1 wide open. With air control the 2 air hole have the oring just above them. So u really have to close the sleeve to tighten up the draw. In the pic is how I'm vaping it and as u can see it looks almost closed. It's a bit tighter than my lite but I noticed if I open any further it feels wide open so...
Sent from my iPhone using Tapatalk
The Origin is nice and I like the look. Couple things I found though I wasn't fond of. There is a beauty ring on the switch just above the locking ring. That ring is held in place by an oring. When locking the switch that ring will move and at times be crooked. Again it's held in place by an oring, I may look for a bit larger oring to hold it in place better. No big just wasn't excited by it. The other is u can adjust the firing pin/screw in the switch. I believe is to make the switch throw shorter..I think. So when locking the switch that adjustment screw will move as I'm turning the locking ring. It can then move the pin out of reach of the bottom of the batt, again not end of the world but not fond of it. It may be user error as today was first day with both. It does look the cats meow as a hybrid in 490 mode.
Ken
edit: haven't tried juice control, haven't had a dry hit or even a hint towards it. I saw some vids where they weren't even using it. So for now I keep juice control closed as it seemed to wick fine. Air control at wide open is a tad more open then the KF lite and I think about the same as 3.1 wide open. With air control the 2 air hole have the oring just above them. So u really have to close the sleeve to tighten up the draw. In the pic is how I'm vaping it and as u can see it looks almost closed. It's a bit tighter than my lite but I noticed if I open any further it feels wide open so...
Sent from my iPhone using Tapatalk
Last edited:
thanks for taking the time to do that....again...i've been eyeing that combo for a while....nice to read a hands down short review like that.....
it would be cool if they made a brass aqua cover or something....
This is a good buy for me. I wanted another good silica atty and already have an Ithy and obv the KF's. The brass and SS r a nice combo. For those that like hot ... vaping the Aqua will get er done. I saw a FB post where someone set it up at .4......howuuuudoin.
Ken
Ken
3 Words- Nemesis Switch Magnets! (Vaperev if you must)still can't get enough of my setup
After owning the TI Steam Turbine... I have found a new love...
TITANIUM!
Can some one throw up some pics of titanium mods that are currently available?
Just what to see what is out there.
Sent from my Nexus 4
TITANIUM!
Can some one throw up some pics of titanium mods that are currently available?
Just what to see what is out there.
Sent from my Nexus 4
Sure you got all the parts there... ya left a couple of o-rings on
lal, i know i know, when i was about to pull them out (insulators as well) i had to stop myself from going completely insane, otherwise i'd probably start melting the parts to show the initial state before molding
on the list mate, i saw you writing on their awesomeness and i will be getting them shortly, along with extended post.
trying to control myself here, avoiding all cape gear sites and all, otherwise the shopping list will exponentially increase, I really want to do an "at-home" setup with brass button and top cap with an aluminium tube in between, al topped off with a decent dripper. Not to mention my new found affection towards the Geobukseon mod (I believe I really need it hehe)
- Status
Similar threads
