Holy grail vape setup whats yours
- Thread starter RogerWilco357
- Start date
- th_trl_thread_readers 0
- Status
REO 18650 woodvil with Mark bugs chalice (right) and pdib OliveR with Mark bugs chalice (left)
REO grand with vicious ant cyclone
I rotate between these three every day
Last edited:
I'm another Reovilleite. I have Provaris, authentic KFL Lite+, and Russian 91%. To me, The Reo grand w/RM2 and/or Cyclone are far better with regard to taste and vapor. Just saying!!!!
anything I don't have to take from my kids college fund for lol. to me I dont see a difference. give me a no name mech mod without wires and buttons and spot lights that sing the national anthem and 3 feet long. best vape I have to date. a 35 dollar mech mod clone and a 30 dollar kayfun clone blows fatter clouds than any dna 30 or provari could. I have about 500 dollars worth of fancy devices and tanks that cant hold a candle to my mech mods. just my humble opinion.
A dual coil between .2Ω-.5Ω with lightly flavoured juice at either 7.2mg or 14.4mg Nic on Reo + Rm2...
It doesn't get any better
It doesn't get any better
My "Holy Grail" setup of the day:
Expromizer v1.1 on my DNA30 clone box:
I built a massive coil in the Expromizer for use on the DNA30 box, 10 wraps of 26ga at 2.2mm for 1.1Ω and firing it at 20-25watts depending on my mood. Loving it!
Expromizer v1.1 on my DNA30 clone box:
I built a massive coil in the Expromizer for use on the DNA30 box, 10 wraps of 26ga at 2.2mm for 1.1Ω and firing it at 20-25watts depending on my mood. Loving it!
Today its my Nemesis with a Kayfun 3.1, 1.3 ohm, 30 gage micro coil wicked with Peaches n cream ecru yarn, filled with Collosuss Cyclops juice (6mg).
Yesterday was my Sentinel M16 with a Nimbus dripper with drilled 1/16th airholes, dual 28 gage micro coil build @ .7 ohms, wicked with cotton.
Those are my typical go to setups for my days off work where I can have a good looking setup that im not worried about dropping on diamond plate or banging up in some other way while at work.
When I am working its usually my beat up, eldery SID and Rocket RBA (built w/30 gage micro coil and cotton @ 1.5 ohms). Its dependable, consistent through my batteries charge and fairly expendable if it should get banged around or worse.
All three are pretty dang satisfying setups for me. I do like having several rigs that work for me so I guess there is no one holy grail in my case.
I need a pretty RDA to go with my Nemmy though...
And a Caravella...
And a Taifun...
And more Sony vtc5s...
And more tasty, creamy juice...
A tank car of Five Pawns Grandmaster...
And a Reo Grand...
And - and - and...
Yesterday was my Sentinel M16 with a Nimbus dripper with drilled 1/16th airholes, dual 28 gage micro coil build @ .7 ohms, wicked with cotton.
Those are my typical go to setups for my days off work where I can have a good looking setup that im not worried about dropping on diamond plate or banging up in some other way while at work.
When I am working its usually my beat up, eldery SID and Rocket RBA (built w/30 gage micro coil and cotton @ 1.5 ohms). Its dependable, consistent through my batteries charge and fairly expendable if it should get banged around or worse.
All three are pretty dang satisfying setups for me. I do like having several rigs that work for me so I guess there is no one holy grail in my case.
I need a pretty RDA to go with my Nemmy though...
And a Caravella...
And a Taifun...
And more Sony vtc5s...
And more tasty, creamy juice...
A tank car of Five Pawns Grandmaster...
And a Reo Grand...
And - and - and...
Last edited:
I'm not going to jump on the "whatever brands I'm using" bandwagon.
18650 VV/VW mod, 3ml gennie.
Brands don't matter. That will get me the use time I need to make ecigs about the same hassle as "grab a pack and go" cigarette smoking mentality.
18650 VV/VW mod, 3ml gennie.
Brands don't matter. That will get me the use time I need to make ecigs about the same hassle as "grab a pack and go" cigarette smoking mentality.
Mine is currently the bronze Provari topped with an Aspire Nautilus 
Last edited:
Super X - I need to know where you got, or how you made that door for your Reo. Very sweet.
You could probably do that by taking some sheet metal snips to a circuit board, then sanding down the rough edges
It was made by my man pdib. He made a few and gave them to several of is and is fresh out. But he is making killer bottom fed mods - the OliveR
Here's mine
And yes, it is one of my holy grail setups
That is damn spiffy. Beautiful!
It was made by my man pdib. He made a few and gave them to several of is and is fresh out. But he is making killer bottom fed mods - the OliveR
Here's mine
And yes, it is one of my holy grail setups
My very favorite setup is some sort of power source, 3.4 volts to 7.4 volts, fixed or variable volts or wattage. Connected to a mechanism with a coil, air / liquid flow that will heat the liquid that is dripped, filled, injected, squonked. Anything form a 306 pre-built atty to a dual coil gennie will do, to vaporize my latest DIY creations. Does it make vapor....than that's my favorite....
currently v3 flip gold and zenith. both are clones. we will see if the mephisto beats the zenith
It was made by my man pdib. He made a few and gave them to several of is and is fresh out. But he is making killer bottom fed mods - the OliveR
Here's mine
And yes, it is one of my holy grail setups
Hey SuperX.. I've seen that pic a couple of times now... very nice
... my eye's keep getting drawn to that red thing in the background.. what is it? 
Hey SuperX.. I've seen that pic a couple of times now... very nice
Looks like a bird feeder.
Hey SuperX.. I've seen that pic a couple of times now... very nice
Yes, funk is correct. It's a hummingbird feeder
Last edited:
- Status
Similar threads
