How do you carry your MVP? :D
- Thread starter VickyWood
- Start date
- th_trl_thread_readers 0
- Status
i never took mine out the house, but after gifting it to a friend - he sticks it in an OLD nokia phone case and clips it on his hip
i used to rebuild my evod coil heads and i would order these https://www.fasttech.com/p/1593911
i still rebuild friends for them, but i have 3-4 of these bags of coils so i dont need to order any for a GOOD long time
i still rebuild friends for them, but i have 3-4 of these bags of coils so i dont need to order any for a GOOD long time
im sure there is a thread somewhere floating around the forums about rebuilding iclear16/30's. but thats up to you weather on not you want the "hastle" of rebuilding the coils heads. every tank system is different sadly :/ and the level of "hastle" goes up depending on brand... i stuck with rebuilding kanger evods/protanks because they were the "less fiddley" of the group of tanks i own, to rebuild. i tried to recoil my kanger t2's but those were all soldered 
Vicki,
If you order the prebuilt wrapped wires from fastech all you have to do is assemble them.
Here's a video that shows the complete procedure (including wrapping the wire). However, all you would have to do is disassemble the old coil and install the new coil that was prebuilt. It takes so little time compared to wrapping your own and saves SO MUCH MONEY over buying new coils. You wouldn't even have to buy an ohm reader as your MVP can check the resistance and let you know if you have a short.
Mini Protank Micro Coil Rebuild
If you order the prebuilt wrapped wires from fastech all you have to do is assemble them.
Here's a video that shows the complete procedure (including wrapping the wire). However, all you would have to do is disassemble the old coil and install the new coil that was prebuilt. It takes so little time compared to wrapping your own and saves SO MUCH MONEY over buying new coils. You wouldn't even have to buy an ohm reader as your MVP can check the resistance and let you know if you have a short.
Mini Protank Micro Coil Rebuild
Last edited:
Not an MVP but in iStick - I keep an old glasses case of the type with one end open in my jacket pocket. Just drop it in.
Without the glasses case, it would typically fall on its side in the pocket.
Will often pull the case out and drop it in a cup holder when I'm driving. It keeps the tank from rattling against the sides.
Without the glasses case, it would typically fall on its side in the pocket.
Will often pull the case out and drop it in a cup holder when I'm driving. It keeps the tank from rattling against the sides.
Honestly, the bulky nature of the MVP is why I eventually had to upgrade. If it wound up crooked in my pocket, the weight would put pressure on the tip of the iClear tank and break it. I eventually switched those for a ProTank, but that just made the whole package even heavier.
Going through the old cell phone box a couple months ago I came up with an idea. 3M double sided tape made for a daily rock solid hold.
The new but already disappointing Areotank Giant with the broke MVP both dug out of the junk drawer for a cool photo shoot but junk!
In making this post and putting the Giant back on the Istick it may stay
for a minute but will probably get dropped back into the junk drawer soon.
The new but already disappointing Areotank Giant with the broke MVP both dug out of the junk drawer for a cool photo shoot but junk!
In making this post and putting the Giant back on the Istick it may stay
for a minute but will probably get dropped back into the junk drawer soon.
I would just order from FastTech. They deliver worldwide and shipping is free. Most people pay the extra $2.00 to get the order a little faster.
However, if you wish to rebuild them here is a place you can order wire/wick in the UK:
1. Cloud 9 Vaping - Cellucotton (Rayon)
2. The Vape Mesh Company - Source for A1 Kahthal. The wire listings state both the AWG and the wire diameter (e.g. 0.28mm etc.)
Just a side note: I got into rebuildables (RDA's/RTA's) using my MVP. Who knows, maybe someday soon you will too!
Glad ya like it Vicky! Here's an even better pic for him. I left the leather back and just cut it with some
good scissors. I found one with a swivel but didn't really need it. 3M tape, you don't want to skimp there.
Glad ya like it Vicky! Here's an even better pic for him. I left the leather back and just cut it with some
good scissors. I found one with a swivel but didn't really need it. 3M tape, you don't want to skimp there.
A lighter around the edge cleans the cut up too when you're done. Mine here was after many days of use.
LOL Oh man my hubby is moaning at me, U might blow it up!!!!!!!!!! U have this lovely (cig) and ur messing with it!!!!!!!!!!! just go to shop and buy theirs!!!!!!!! sigh, its not worth the hastle, I guess i'm buying pre made shop coil/wicks
I guess i'm buying pre made shop coil/wicks
We'll see. It can get expensive with Kanger, but cheaper with Innokin or Aspire.
I've got a little gadget on the way that makes coils.... the rest of it is easy... the cotton wool and assembling I don't mind so much.
Holy Moses that's a big tank! How well does the MVP fire that? I had issues getting a good hit from a nautilus mini.Going through the old cell phone box a couple months ago I came up with an idea. 3M double sided tape made for a daily rock solid hold.
The new but already disappointing Areotank Giant with the broke MVP both dug out of the junk drawer for a cool photo shoot but junk!
In making this post and putting the Giant back on the Istick it may stay
for a minute but will probably get dropped back into the junk drawer soon.
- Status
Similar threads
