... or that there was so many different ways to do it. I'll be trying Lisa's method.
How I fill my 6ml REO bottle
- Thread starter jifjifjif
- Start date
- th_trl_thread_readers 0
- Status
... or that there was so many different ways to do it. I'll be trying Lisa's method.
A 10ml bottle in your REO?well yeah, now I carry 2 reo's, and each has a 10ml bottle so I really never have to touch any bottles when I'm out and about anyway
I take the door off, use it's corner to pop the bottle out, pull the tube and bottle, pop my top off, refill from my 200 ml reserve, put the tube back in and snap the top back on, curse my greed when I realize I filled it too far and have a juicy mess, pinch the bottle end and rinse under water, dry, take the the of the tube and place it on the inside of the 510, than put the bottle in using the pressure to pop the tube onto the post,
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
well yeah, now I carry 2 reo's, and each has a 10ml bottle so I really never have to touch any bottles when I'm out and about anyway
Vmod bottle mod?
Sent from my iPhone using Tapatalk
yeah, I like the 10, takes the same space, cap doesn't need any oring and it squonks easier, softer bottle with more room for compression with less resistance. also the fill hole is larger so it's much easier to fill. the vmod 10ml bottle is thin and flimsy compared to robs 6ml, that's for sure and that's why he doesn't carry or offer them, I always half expect it to split at the seem some times but I haven't had one fail yet and I use them hard. they're cheap to replace if it did fail and I bought extras, about the only thing to worry about is if it split while you were out but again, been using one in my metal grand over 4 months now no problem yet, just inspect it every once in a while and avoid positioning it so it folds on a seem when you squonk
ha, I didn't know the first reo's were set up for lefty's
Yea, I'd be so frustrated and never figure out the bottle threads were backwards.
Good methods all, mentioned in this thread. I don't have much hassle with my Grand.
On my Mini2.1 and the 3 ml. bottle, my arthritic fumble thumb fingers make a mess most of the time. Still and all I love the little rascal, fits in my shirt pocket really good.
How do y'all fill the 3 ml. Mini bottles without making a mess. I have trouble getting the tube back in and the cap screwed on and making a bit of a mess. Hints?
Thanks
On my Mini2.1 and the 3 ml. bottle, my arthritic fumble thumb fingers make a mess most of the time. Still and all I love the little rascal, fits in my shirt pocket really good.
How do y'all fill the 3 ml. Mini bottles without making a mess. I have trouble getting the tube back in and the cap screwed on and making a bit of a mess. Hints?
Thanks
Leave the end of the tube in and fill with a bottle that has a blunt needle cap on it.
Last edited:
I've always used needlenose pliers or tweezers to push the tube back on the nipple cus I cant get my fingers in there lol ..
and before I did the cap mod I would screw the cap on and off whilst pushing the side of it against the centre divide flap in the reo and holding the very bottom of the bottle edges to stop juice squeezing out
and before I did the cap mod I would screw the cap on and off whilst pushing the side of it against the centre divide flap in the reo and holding the very bottom of the bottle edges to stop juice squeezing out
Leave the end of the tube in and fill with a bottle that has a blunt needle cap on it.
Thanks y'all. I'll give both a shot.
Did I... Did I not link?
Just in case
http://www.e-cigarette-forum.com/forum/reos-mods/521257-just-did-bottle-mod.html
Sent from my iPhone using Tapatalk
Just in case
http://www.e-cigarette-forum.com/forum/reos-mods/521257-just-did-bottle-mod.html
Sent from my iPhone using Tapatalk
sorry.... I just read my post.. and was ment to say I hold the cap tight in the corner against the centre flap with my thumb and I unscrew the bottle .... not the cap
- Status
Similar threads
- Locked
