How to lighten the draw on the eGo

[aphlaque_duck]

After switching from atomizers to cartomizers, I found the draw on the eGo to be much too stiff. It turns out the diameter of the black paper wrapped cartomizers is 9.44mm whereas the diameter of the atomizer is 9.09mm. This causes a huge reduction in airflow.

All you need to do to fix it is shorten the shroud just a hair. Because of the taper, this brings it down to a point where the diameter is a little bigger and it gives the needed clearance. This also makes the cartomizers easier to replace because they don't stick to the shroud as you're turning them. There is no cosmetic change to the eGo if you do this carefully.

I would recommed doing this with a belt or disc sander and 150 grit paper. I suppose you could also do it with a file but that is likely to mar the finish. Go slow so it doesn't overheat - just sand a little, wait, sand a little, wait. Only takes a few seconds.

I didn't need to fine tune this. Once the restriction is eliminated, the impedance is controlled by the cartomizer and is just right.

 

[g123456e]

After switching from atomizers to cartomizers, I found the draw on the eGo to be much too stiff. It turns out the diameter of the black paper wrapped cartomizers is 9.44mm whereas the diameter of the atomizer is 9.09mm. This causes a huge reduction in airflow.

All you need to do to fix it is shorten the shroud just a hair. Because of the taper, this brings it down to a point where the diameter is a little bigger and it gives the needed clearance. This also makes the cartomizers easier to replace because they don't stick to the shroud as you're turning them. There is no cosmetic change to the eGo if you do this carefully.

I would recommed doing this with a belt or disc sander and 150 grit paper. I suppose you could also do it with a file but that is likely to mar the finish. Go slow so it doesn't overheat - just sand a little, wait, sand a little, wait. Only takes a few seconds.

I didn't need to fine tune this. Once the restriction is eliminated, the impedance is controlled by the cartomizer and is just right.

duck,

Are you talking about sanding down the ego cone so that it is shorter? I like to use 801 atomizers with my ego sometimes and don't use the cone then since it won't fit. I have extra cones and wanted to modify one for the 801 atty. So you are saying I can just sand it down with a belt sander?

 

[aphlaque_duck]

Yes I'm talking about the cone. Just sand about 1mm, or as much as needed, off the narrow end.

 

[GrandPoobah]

I ended up drilling a tiny hole in my cone. I also use cartos with it, but still prefer an atty. I didnt want to alter the draw permanently because of this. I also didnt want to have different cones for different things.

I keep my finger over the hole and let go get to more of a draw. Just make sure if you do this to mark the spot while the cone is still on the eGo so it lines back up correctly. Start with a tiny hole first and work up to your preferred draw.

 

[Switched]

Another trick would be to remove the paper, or buy the stainless 510s. Alternating the draw to suit the cartos ultimately changes the draw for regular attys as well. To some this makes little difference, to most a large change in performance, unless you remain with cartos.

 

[crand]

Another trick would be to remove the paper, or buy the stainless 510s. Alternating the draw to suit the cartos ultimately changes the draw for regular attys as well. To some this makes little difference, to most a large change in performance, unless you remain with cartos.

I just grab a corner of the tape wrap on the carto and pull up 1/4 in or less and trim it off with a knife. Removing that small bit of 'over-wrap' is all it takes.

 

[aphlaque_duck]

I ended up drilling a tiny hole in my cone. I also use cartos with it, but still prefer an atty. I didnt want to alter the draw permanently because of this. I also didnt want to have different cones for different things.

If drilling holes I would think it's best to do it near the narrow end of the cone. This keeps the airflow running down the length of the carto to cool it down. That seems to be pretty important with the cartos to make them last longer, especially if you're chain vaping.

 

[bhima]

Or you could of course just ditch the cone. It might not look as nice, but it sure is easier and it allows you to use different atomizers such as the great 306 atty. Sorta reminds me of that joke: The US spent 32 million dollars to create a pen that would write in zero gravity, the Russians used a pencil.

 

[Drozd]

yeah I just peel the carto wrapper...and/or adjust the airflow in the adapter I'm using

 

[markimar]

anyone find something to remove the glue off a carto?
Nhalers 510's under the black sticker are silver but I can't get rid of the stupid glue!

 

[crand]

anyone find something to remove the glue off a carto?
Nhalers 510's under the black sticker are silver but I can't get rid of the stupid glue!

Try a product called GooGone. It's an amber colored liquid that comes in a see through plastic bottle. Most drug and grocery stores carry it in their hardware section. You can also use WD40 [spray it on a rag not on the carto]

 

[Drozd]

I've heard that if you refridgerate the cartos the labels come off easier with minimal glue..don't know if thats the case for those specific ones...
rubbing alcohol and nail polish remover work well too...

But what I actually do is use a razor blade/utility knife...takes longer but you can scrape the label and glue off in strips and leaves minimal glue...then I take an alcohol prep wipe and wipe down the carto and while the left over adhesive is still wet I just give it a good rub down with a dish towel..

 

[tazzmann]

of course you can always drip and that would save all the problems.

 

[Switched]

of course you can always drip and that would save all the problems.

Considering this particular post was wrt cartomizers. We welcome your informed input and will take it under advisement

 

[GrandPoobah]

careful with googone. DO NOT get it in the filler.

I've heard of companies selling ones without the sticker wrap. this too would improve the draw

 

[tattooer601]

naptha..........or zippo lighter fluid removes adhesive reside very well.