how to make clouds with a tobh

[im_coryy]

So I just bought a tobh today. However it doesnt make as big of clouds as my old igo m (I had to get rid of it due to a spinning center post) so my question is how do I produce HUGE clouds with my tobh without having to mod it.

Right now its at .5 ohms on a brass nemsis with a sony vtc5 battery. 28 guage kanthal with 5 wraps. Duel coils.

 

[wonkeypickle]

sounds to me like the only thing holding you back is your inhale time, other than that rebuild lower if you're so inclined. however realize that the difference between say a .2 ohm coil and your .5 ohm coil isn't going to be life changing. if you truly feel that it is your build that is not "chuckin the vapor", i would recommend personally going down to 25 or 24 gauge wire.

 

[VapingTurtle]

Use more VG.

 

[jpcwon]

Your Tobh can produce great vapor, rest assured. I have both a v2 and a v2.5 and both are putting out great vapor. As mentioned above, you can try dropping your gauge (bigger wire), or try getting creative with your builds. For instance, here is a build I did on my Tobh v2. I used 24ga Kanthal, but I made my coils so that they are perpendicular to the air holes.....this build produces a LOT of vapor and the flavor is great too! Maybe give this a try?

View attachment 360788

 

[classwife]

Moved to Rebuildable Atomizer Systems from APV Discussion

 

[CRW78]

26g 5-6 wrap parallels. I use a qtip when I wrap my coils. Parallels bring forth much vapor!

 

[jpcwon]

26g 5-6 wrap parallels. I use a qtip when I wrap my coils. Parallels bring forth much vapor!

That they do!!

 

[el Jexican]

You can try twisting your 28g or just user lower guage wire.

 

[brianc11111]

braided wire........quad 28ga 1/8th id... 4 wraps .18ohms
lots of vapor and good flavor







and get rid of the tabs

 

[Blind Squirrel]

and get rid of the tabs

Everyone I know with a Tobh does this.

 

[im_coryy]

How can I remove the tabs. Yes they seem pointless. They just kind of get in the way.

 

[im_coryy]

Also if I twosted my coils to make them thicker more wraps would be required to hit .5 this also means more surface area as more coil hits the cotton so that should mean more vapor right?

I want clouds. That nic buzz first thing in the morning is a wonderful feeling. Somethig ive inly gotten from blowing clouds. Ill also try to increase my inhale time. Ive tried getting a buzz from my kayfun but it just gradually gives me nicotine without the buzz:/ also if it helps I drip 12mg

 

[cobyatch]

Running a dual parallel 26g 6 wrap around a 5/64 drill bit. Came out to .18 and it makes clouds lol. It's kind of a hot build though. Considering drilling between the airholes and turning them into slots.

Removing the tabs:
https://www.youtube.com/watch?v=uerHGIOy63g

 

[CRW78]

braided wire........quad 28ga 1/8th id... 4 wraps .18ohms
lots of vapor and good flavor


View attachment 360791 View attachment 360792




and get rid of the tabs

Holy mother of God!!!

 

[brianc11111]

Holy mother of God!!!

loads of vapor and improves flavor.......also vapes a lot cooler than 22ga at same ohmage

check out the braided wire thread in the coil building section

 

[juggalofisher88]

This does pretty good twisted 28g parallel with 24g .2ohms little lower than i like

 

[CRW78]

I think I'll try a 3 strand twisted ribbon..

 

[juggalofisher88]

I think I'll try a 3 strand twisted ribbon..

After your done wrap a peice of ribbon like a clapton around it.
I did this in single coil and it was great

 

[Uncletattoowhat]

Running a dual parallel 26g 6 wrap around a 5/64 drill bit. Came out to .18 and it makes clouds lol. It's kind of a hot build though. Considering drilling between the airholes and turning them into slots.

Removing the tabs:
https://www.youtube.com/watch?v=uerHGIOy63g

Literally the exact same setup I run. Although, I added 3 holes up and right of the stock 3 to replicate the CCI Militia RDA in addition to cutting the tabs.

 

[ddkl7780]

No need for tabs cut those off right away