I cannot build anything
- Thread starter gel drops
- Start date
- th_trl_thread_readers 0
-
- Tags
- kayfun burning
- Status
Not real sure exactly what I do have anybody got any ideas on this one,both of the two videos that I have watched don't exactly look like the Fogger 5.0 that I got so I'm clueless.I purchased this from a vendor called ChinaBuye..
Last edited:
Yes but its in the top portion of the atomizer that's another thing that concerns me I have not tried to remove it however.Mccannch,if you don't mind and get a chance check that vendor out and see what you think.
Last edited:
That should unscrew from there without issue. As for the wonky post after looking at it, I think you can make it work. I would suggest building your coils and run you negative leads parallel from the "inside - out" that should eliminate the crazy long lead needed to insert them opposite to each other. It's worth a try to see if it will work.
Aqua V2 did not come with a drip tip,I am beginning to think that I got a lot of junk on my hands.
My Eleaf Lemo came pre-built. It is a rebuildable (and I highly recommend learning to build coils...it's not that hard) and I am still using the coil it came with. And it wicks much easier than the Kayfuns and Russians.
looks nice..I think I need to take a little break for an hour or so..Lemo is still rocking,not going to let the other atomizers spoil the day.
So I no longer need the lemo......i just picked up a kanger sub tank. Really couldn't afford it, but omg this thing is awesome. I haven't even used the rba head on it (building it will be very similar to the kayfun, but there juice channels are quite a bit bigger) I'm using the 1.2 ohm occ (organic cotton coil) it came with. This is the first stock coil I've been happy with. There airflow is great. I've been ruining it at 20 watts, and it hits like a dripper. I had to drop to a 6mg juice in it 
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
Oh, at 25mm, it fits on a panzer mod perfectly
I'll take more picks later......
Sent with one hand, the other is busy vaping.
I'll take more picks later......
Sent with one hand, the other is busy vaping.
Pretty,Kanger so many out these days which one is that one ? 1.2 Ohms..Looks like it holds quite a bit of liquid,I am all for that.Never mind I forgot to look ^^^^.
Going to try in the morning to see if I can get the negative post in the right position on the Fogger 5.0.I have a feeling it's going to do me like the SQuape did that FT even stopped selling that particular version that I ordered,that will leave me with the Orchid V4,the Billow and the Aqua V2 that are brand new,no mop needed here not going through that mess anymore it's just not worth it to me,for me it kinda takes the fun out of it being when I get something that I cannot get to work properly,I know what my capabilities are when it comes to making a build,i am also going to do my homework on a particular atomizer before I buy it which I have not been doing that.What really matters to me is that I have something that works properly that produces decent flavor and a good TH and don't leak everywhere.
With the occ coil setup it holds 6ml of juice! It comes with two occ coils, a 1.2 ohm and a .5 ohm, and also comes with an rba type buildable head (that came pre built with a .5 dual coil). I opted to use the 1.2 ohm first for the better battery life. Though I did try out the rba head for a bit....my god this thing kills the kayfun, then digs it up and kills it again
It kinda hurt to spend so much ($50), but I finally have a best of both worlds set up....a tank that feels like a dripper- Status
Similar threads
