I cannot build anything
- Thread starter gel drops
- Start date
- th_trl_thread_readers 0
-
- Tags
- kayfun burning
- Status
everything i have is from FT.. other than taifun gt, and taifun gt 2. aqua v2 is from FT also. the way i have been doing the wicking is just using thin wick. but from what i have seen in the video, you would wick it just like any other, then you split the cotton outside of the coil in two. test by packing the channel with half of the wick outside of the coil. if it's good, you cut the other half off. seems to be easy enough.. but first try i had, i had ton of burnt taste. second time, it leaked. so i just went with thin wick. but with thin wick, thin wick leaks a little. i'll have to try again to build a right wick.
So I just did an experiment. I built a Clapton inside one of my sub tank occ heads. 32 gauge around 28 gauge, 4 wraps on a 3mm bit, came in at 1.1 ohm. The legs were a little tight, but omg the flavor is amazing 
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
i like their juice review. they are funny. sometimes, rip tripper is also funny.. but he goes overboard with his down south act. vaping with 420 is ok most of the time, but crack himself up too much. i like ruby roo. she's very informative and i like her vape drink paring thing.
I saw I think his name is Matt on suck my mod,and he pretty much destroyed one of the heads trying to take it apart did you have any problems taking it apart I'm not sure I got the proper tools to take on something like that.
He did it wrong. You need no tools except clippers to trim the wire and something to wrap on that is 3mm.
Pull out the bottom pin, then pull out the rubber gasket. Pull out the old coil through the bottom (may need pliers to do so. It will deform the old coil.... But who cares, cause you are tossing it
). Give it a good rinsing. Make your new coil on the 3mm jig/bit, leaving the legs fairly long. You will load the new coil through the top hole, legs first. Run your 3mm bit through the wick hole on one side, then through the new coil and out the other wick hole to hold the coil in place. Position legs, reinsert gasket and pin, trim legs (trim as close as possible, or it doesn't fit the base well), pull out bit, thread wick through holes and trim. Easy peasy
Here is a video...
http://m.youtube.com/watch?v=6w2p09Iu11U
Sent with one hand, the other is busy vaping.
http://m.youtube.com/watch?v=6w2p09Iu11U
Sent with one hand, the other is busy vaping.
After you build a new coil...wick it like this.....http://m.youtube.com/watch?v=WMUOtwsd7_E
Instead of how the first video shows, it works better, less dry hits
Sent with one hand, the other is busy vaping.
Instead of how the first video shows, it works better, less dry hits
Sent with one hand, the other is busy vaping.
Another note...... If you are going to shoot for .5 ohm, use 26 gauge. My preferred in this tank is .8 ohm, which is 6 wraps of 26 gauge on a 3mm bit
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
So have you tried an occ rebuild yet?
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
I looked the other day and most of the threads on here had been moved,I was just not sure what was going on with that.I am still using the exact same .57 ohm head it came with,they do last that I will say,but 18mg liquid its all I have at this time and it's not to lung friendly.
Last edited:
Lol.
If you like the flavor, get yourself some zero Nic of the same stuff and cut it down
Sent with one hand, the other is busy vaping.
If you like the flavor, get yourself some zero Nic of the same stuff and cut it down
Sent with one hand, the other is busy vaping.
It still hits like a beast, even with the 1.2 head
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
I did lower the wattage down to around 12 watts it's not to bad.It still hits like a beast, even with the 1.2 head
Sent with one hand, the other is busy vaping.
You must be in a sub tank fog.... Haven't posted here in days
Sent with one hand, the other is busy vaping.
Sent with one hand, the other is busy vaping.
- Status
Similar threads
