Igo-l wow

[GaLacTic]

Got my IGO today from Randy Davis at RTD Vapor wow im so in love with it.. so far tried dual coils and now im on a single coil at .7 ohms i did bore out the air hole a bit by the way i looked high and low for this dripper and RTD Vapor was the only place that had them in the us anyways.. great service also !!! so what have you guys done to get the best results from these beasts?

 

[StaircaseWit]

I run German silica in it, doubled over in an "S" pattern to fill the well with wick. I don't run a SLR coil in it because it's on my provari for work or otherwise away from home. 5 wraps of 30g at about 1.7ohms. Good stuff at 4V. It's a solid little dripper.

 

[beanpusher]

i did a single wire dual coil setup with 26awg kanthal a1 3/4 wrapped @ .3 ohms with 3mm cotton wick dbl'd thru

 

[aPandaz]

i did a single wire dual coil setup with 26awg kanthal a1 3/4 wrapped @ .3 ohms with 3mm cotton wick dbl'd thruView attachment 193173View attachment 193174View attachment 193175View attachment 193176

I'm wondering what kind of battery you are running and if it can handle that drain?

 

[aPandaz]

I'm running a 0.8 ohm coil on a 3 fold 2mm silica wick now. Coil is 32g twisted, 2/3 wrap. Hole is bored out to 1.6mm. Nice little cloud maker.

 

[GaLacTic]

I'm wondering what kind of battery you are running and if it can handle that drain?

wow looks sweet i think im going to have to recoil it like yours bro is that peaches and cream cotton? i have looks i bit hard to do but im up for the chalange thanks for the info i will report when i do it ... what size bit did you use to pre coil?

 

[GaLacTic]

sorry wrong quote..

 

[beanpusher]

wow looks sweet i think im going to have to recoil it like yours bro is that peaches and cream cotton? i have looks i bit hard to do but im up for the chalange thanks for the info i will report when i do it ... what size bit did you use to pre coil?

i used a 3/32 rod and pure cotton yarn from walmart single wire just made it easier to attach since theres no wire holes in the post

the single wire dual coil was just testing the limits with the igo-l not my everyday vape. i don't recommend running a setup like that at all.

my daily vape with the igo-l is with 28awg 3/4 wrapped over 3x looped cotton @ .8 ohms

 

[Quigsworth]

Any modders out there think this could be made to bf?...I've modded a number of dripper ERA's over to bf, just wondering if this is the same???

 

[Astronahmer]

Any modders out there think this could be made to bf?...I've modded a number of dripper ERA's over to bf, just wondering if this is the same???

I have a Igo-l that I don't really use, maybe we can get this project going?

 

[Quigsworth]

I have a Igo-l that I don't really use, maybe we can get this project going?

I've checked several site looking for good pics of the guts...it looks like it's about the same configuration of an ERA. With the ERA's, I remove the screw from the center post and run a 1mm drill bit right down through it on a drill press, I then lay the ERA on it's side and run the bit though the post just up from the base for the juice to exit...this looks like a similar process would work. The only issue is going to be whether this will fit into any dripcup (which is doubtful, it looks quite wide)...fortunately I have a mod (home made) that doesn't have a dripcup, I use o rings...wth, for $20 it's worth the experiment...