okay so my ego c is not making any vapor, tried three different atomizer both my cones and my batteries. its not my batteries because i can get vapor with the fluxomizers i have, when i put the ego-c on it sounds like its working but no vapor comes out the only thing i could think of is its my juice what doesn't make sense is i was just using the same juice before it stopped working so I'm really wondering whats up anyone have any ideas throw them at me thanks.
im stumpped (ego-c)
- Thread starter kilascay
- Start date
- th_trl_thread_readers 0
- Status
must have been my juice don't understand why it quit making vapor that was weird.
Do you hear it working? Is the tank tip clogged? To much condensation in the head?
yes i hear it working i think I've narrowed it down maybe too much juice getting into the atty because when i take the tank off and hit it a couple times i get some vapor the thing is I've tried three new attys and all are having the same problem so its not the wick. don't know what else to do I've also tried three different tanks new ones .. still no go. thanks for your rep lie.. i think i have a defective cone the draw seems a little tight.. guess ill order a type b
Last edited:
Sounds like your attys might be flooded which usually comes from dragging too hard. The eGo-C really works best using a soft, slow drag. Think of it as the difference between slowly sipping a fine cognac after dinner and gulping down a cold beer on a hot day. 
A few things. In case you're using them, soft caps on the c tanks can cut off air flow. They do with the new B tanks. Soft caps on the t's, hard caps on the c's. The atty holder(cone) might have the centerpost pushed in to where you're not getting contact with the batt. You can pick that out a bit with the dental pick or strong toothpick. OR... usually no vaper - if everything is working - is a flooding issue. I'd stove pipe (no tank) that atty dry... but you may have a defective one....
The atty holder(cone) might have the centerpost pushed in to where you're not getting contact with the batt. You can pick that out a bit with the dental pick or strong toothpick. OR... usually no vaper - if everything is working - is a flooding issue. I'd stove pipe (no tank) that atty dry... but you may have a defective one....
Could be a bad cone. I had one cone that broke and it did all sorts of things but work lol. I do the exact same thing as Kent, tail pipe it when it gets flooded. I do use the soft caps though on the B tanks with out issue other than when they are really full they have to have a primer puff once in awhile. My B cones aren't Joyetech though so they might be slightly different too.
I'm getting very little vapor with my old cone could it be my barriers or charger .. I don't notice anything and when I take the wick off a Atty it gets red pretty quickly. Just can't figure it out.
Sent from my cm_tenderloin using Tapatalk
Sent from my cm_tenderloin using Tapatalk
I can't see how a cone could make a difference. All it does is hold the atomizer and it's too big to plug up. Did you try changing the base? Are you leaving an air bubble in the tank?
I experienced the same exact performance issue with "C" attys. I "upgraded" my EgoT and bought $80 worth of C cones/atty's. The C atty's are no better than T's, except that they don't leak. Very little vapor production, with zero throat hit. I put a review on the Litecig website and they took it down. Ill never buy from them again- since they regulate and censor reviews..
Anyway-- I left plenty of air gap, used soft and hard caps, tried different juices... nothing worked. I think that the issue is not enough air flow
Anyway-- I left plenty of air gap, used soft and hard caps, tried different juices... nothing worked. I think that the issue is not enough air flow
See my post above please... I really want these to work!!! But again, I think the issue with the "C" is that it doesn't allow enough air flow. I'm stuck with two packs off atty's. Does anyone know of and possible modifications?
If you don't have a Joyetech, try a Joyetech atty if you can get one. They seem to work a lot better. You can also try pushing the wick down in the needle to improve wicking. Or you can get a stardust. I ordered a 5 pack of Joyetech attys and some stardusts and the Joye atty worked a lot better than what came in the kit. However, they're just backups now because I love the stardust.
I found out the fun way that the cones can be bad. One of mine broke into 2 pieces, and never got it to stay together right after that. There is the outside & a little inside piece that the head connects to the battery. After it broke apart it'd either get crooked and ruin caps or it wouldn't connect to the battery or it would just come back apart. I ended up just ordering a new cone.
The 2 pieces:
As for your issue, I don't have a clue what you're doing different. I never have any issues with my C now that I've gotten used to it. It produces a lot of vapor for me too. But I did the trick linked below and took out the tank's 2 pieces on the mouth piece to get a little bit more flow.
Here is a good way to loosen the draw some:
http://www.e-cigarette-forum.com/forum/ego-type-models/267810-ego-c-easier-draw.html
Maybe that'll help you some.
The 2 pieces:
As for your issue, I don't have a clue what you're doing different. I never have any issues with my C now that I've gotten used to it. It produces a lot of vapor for me too. But I did the trick linked below and took out the tank's 2 pieces on the mouth piece to get a little bit more flow.
Here is a good way to loosen the draw some:
http://www.e-cigarette-forum.com/forum/ego-type-models/267810-ego-c-easier-draw.html
Maybe that'll help you some.
- Status
