introducing HELL'omizer™ - EVERLASTING ATOMIZER! ...hits like Hell!

[mwa102464]

So in a nutshell:

As I said the "customer is always right" (we believe in that).
Right now I'm updating the original first post and switching the material to stainless steel.
Let's see what we can do with it.
Forget about the original copper idea.
Stainless steel is the actualy project from this moment.
If we'll be able to do it and work with it, then everybody gonna be happy.
If we fail... then I'll close this thread to not waste your time with a "dead-end" idea.
So I'll keep you all updated.
Subsribe to this thread and come back for the news if you want.
Thanks to everybody for the kind posts and and I'm updating this thread with new infos of the progress ASAP.

Way to go Demon, now your going to draw lots more attention and sales I believe, great to see you've made this change.! Keep my preorder #9 on order now too ! thank you

 

[mwa102464]

Yes... also there are many more problems. It's not an easy thing to switch.



I believe that. And thank you.



Thank you for that too. It's kind of you.



Yeah it does. Or rather... everbody's loving it, which is a great thing.

Makes a lot of sense now to me Demon ! Great change to the SS !!!!

 

[Demon]

Makes a lot of sense now to me Demon ! Great change to the SS !!!!

Cheers to that!

 

[Demon]

I also updated now the original photo in the first post.
Check it out by clicking here:
http://www.e-cigarette-forum.com/fo...ng-atomizer-hits-like-hell-5.html#post2842013

Now it looks like the stainless steel version will look like (in case we'll be able to make it).
Crossing fingers... and prayin' for it.

 

[mwa102464]

I also updated now the original photo in the first post.
Check it out by clicking here:
http://www.e-cigarette-forum.com/fo...ng-atomizer-hits-like-hell-5.html#post2842013

Now it looks like the stainless steel version will look like (in case we'll be able to make it).
Crossing fingers... and prayin' for it.

Demon, is there some way you could post a picture of the inside of this unit with it apart and the top off of it so we can see the inner workings of this Atty. I think it would be much more captivating to your audience so they could see what they may be purchasing.

 

[Demon]

Demon, is there some way you could post a picture of the inside of this unit with it apart and the top off of it so we can see the inner workings of this Atty. I think it would be much more captivating to your audience so they could see what they may be purchasing.

I was originally planning to do that tomorrow with the copper version, but since you guys didn't like the idea we won't spend more time on that version.
We are concentrating now only on the upcoming stainless version.
I'll post many photos + YouTube video when (if) the stainless version is done. (when we'll have minimum 1 prototype to show you)

 

[jlarsen]

No, unfortunately it won't. The bottom of the device is sealed, to prevent leaking. So you cannot push liquid into it from below.
You can only drip into it from above.

I'm assuming then, that it also can't be used with automatic batteries... and it probably isn't recommended for small (180 mAh) batteries? Am I correct?

 

[Demon]

I'm assuming then, that it also can't be used with automatic batteries... and it probably isn't recommended for small (180 mAh) batteries? Am I correct?

Well theoretically you could use them with auto batteries. The bottom of the device is sealed, so it won't pop your auto battery, however I wouldn't recommend you to use this device with a small sized regular e-cig battery.
It requires a bit bigger capacity than that.
We provide you with 2 types of wires (to build low res atty and regular one too).
So you can pick your choice.
But this device will be recommended to use with bigger tube mods (I'm not allowed to mention concrete names here, because it's against ECF rules to mention other suppliers' products).
But it'll run the best on tube mods. Because it simply looks better with them... also because those 18650 batteries etc... will give a nice power to this atty.
But the best choice (what I can personally recommend) is a variable voltage device for it.

 

[supsandroid]

subscribed

 

[Demon]

subscribed

Thank you Sir!

 

[alldayvape]

Looks Great Demon!! Do you have a Youtube vid of the Hellomizer in action? Also, if and when the Steel version comes out, I'll order one for sure!

 

[mwa102464]

I was originally planning to do that tomorrow with the copper version, but since you guys didn't like the idea we won't spend more time on that version.
We are concentrating now only on the upcoming stainless version.
I'll post many photos + YouTube video when (if) the stainless version is done. (when we'll have minimum 1 prototype to show you)

OK THANKS ,, I look forward to seeing your progress move forward Demon.!

 

[Demon]

Looks Great Demon!! Do you have a Youtube vid of the Hellomizer in action? Also, if and when the Steel version comes out, I'll order one for sure!

Please check out my first post in this thread.
Click here:
http://www.e-cigarette-forum.com/fo...ng-atomizer-hits-like-hell-6.html#post2842013

There you can pre-order it! (we don't accept any money right now, you'll only get a pre-order number to stand in line)
And yes: we'll post many detailed photos of the product ASAP + YouTube video too.
Keep an eye on the first post in this thread.
All important updates will be added there (video + photos)!

 

[alldayvape]

Thx Demon, before I put in a pre-order I have a question, and it might have already been asked, so I apologize in advance! This is not based on a *blank*, is it?

 

[Demon]

Thx Demon, before I put in a pre-order I have a question, and it might have already been asked, so I apologize in advance! This is not based on a ce2, is it?

I'm afraid I don't know what you mean by "ce2".
If that's another product from another supplier please send me the question in PM!
We cannot talk about other suppliers' products here. (it's against ECF rules!!)
But if you explain your question to me in PM, I'll answer within a sec.

 

[jackoboy82]

so is this just an atty builder or a tank with an atty to hold juice?

 

[Demon]

so is this just an atty builder or a tank with an atty to hold juice?

Please wait until we'll be able to post more photos to the original first post + YouTube video. Then you'll get answers to all your questions.
No, this is not a tank, not a cartomizer.
This is a REAL atomizer what you can rebuild yourself with the accossories we provide in the starter kit.
You'll see when the photos+video will be added to the first post.

 

[unsure]

I might suggest a video when its possible to and better understand how it works.

 

[jackoboy82]

I get how it works now, just wasn't sure if it held liquid as well

 

[Demon]

I might suggest a video when its possible to and better understand how it works.

Video will be added soon. Please check the first post!