JOYETECH ERoll

[mommysnofun]

Hello to anyone who can help...I'm having a problem...one of my batteries won't charge, even though the blue light will flash if I puff on it. It's only a week old! I've tried changing the cone, atomizer etc. just won't charge (in either of the pcc's I have) Has this happened to anyone else so quickly?!

Also, I've noticed the flavor is diminishing somewhat and I've seen a few people mention what strength, ratio & flavors work best for the eroll, I'd love to know what many more of you are using so I can buy some new eliquid today!! I'm open to trying any flavors, because I'm still smoking an occasional cigarette...not going to beat myself up about it tho.... Thank you.

 

[TennDave]

Hey there- are you sure it's not charging? Did you try putting a drop directly on the little pointed tip of the atomizer and then trying again? I've had instance where I thought it wasn't working and it was just that it wasn't getting any juice. Btw, with e-liquids, for me, I use 36mg in the eRoll in all VG and super concentrated flavors from E Cig : Best Ejuice | Joye eGo & eGo-T | Boge Leo | Cartomizers | E-Liquid | Electronic Cigarettes That's all I use. I typically mix it up so that I have a drop per ml of liquid and it works well for me in my eRoll. Otherwise, I dilute the 3.6% down to 1.8 for my other PV's. Hope this helps!!

 

[Palerider]

Just ordered some mesh and 32 wire from OKC...can't wait to get it and make these eRoll's really shine!

 

[Palerider]

Hello to anyone who can help...I'm having a problem...one of my batteries won't charge, even though the blue light will flash if I puff on it. It's only a week old! I've tried changing the cone, atomizer etc. just won't charge (in either of the pcc's I have) Has this happened to anyone else so quickly?!

Also, I've noticed the flavor is diminishing somewhat and I've seen a few people mention what strength, ratio & flavors work best for the eroll, I'd love to know what many more of you are using so I can buy some new eliquid today!! I'm open to trying any flavors, because I'm still smoking an occasional cigarette...not going to beat myself up about it tho.... Thank you.

Hi!

Ya, like TennDave said...it isn't a bad idea to put 2-3 drops in the atomizer to make sure it has fluid in it. Also, check and make sure the atty is seated properly on the battery contacts. If that does not work, then you may have to contact the vendor for a replacement.

 

[volume control]

Hello to anyone who can help...I'm having a problem...one of my batteries won't charge, even though the blue light will flash if I puff on it. It's only a week old! I've tried changing the cone, atomizer etc. just won't charge (in either of the pcc's I have) Has this happened to anyone else so quickly?!

Also, I've noticed the flavor is diminishing somewhat and I've seen a few people mention what strength, ratio & flavors work best for the eroll, I'd love to know what many more of you are using so I can buy some new eliquid today!! I'm open to trying any flavors, because I'm still smoking an occasional cigarette...not going to beat myself up about it tho.... Thank you.

Does it light up blue to show it charging in the PCC? If you cant get it to light up you can try cleaning the tip of the eroll with a paper towel alcohol but careful not to get any into the hole. Then when you put the battery in, try twirling or rubbing the tip into the contacts to get them to turn the charge light on.


If in all cases no luck, you could have a bad battery. I have 4 batts and one that came with my kit is no good. It charges but i have to draw really hard to get it to kick on =( They are only 9 bucks so i didnt bother trying to return

 

[ccm2000]

I just noticed the blue charge light on the PCC is not a light at all. Just a window to the battery light. Clever.

 

[KrasH]

Does your pcc have a rattle to it?

 

[DawnBella]

Just wanted to be super sure you guys say it is okay to boil the eRoll attys for cleaning. I may tonight. What about the rubber O ring thingy at the bottom. Wouldn't it melt? Thanks!!

 

[volume control]

Just wanted to be super sure you guys say it is okay to boil the eRoll attys for cleaning. I may tonight. What about the rubber O ring thingy at the bottom. Wouldn't it melt? Thanks!!

I have an electric stove so i made sure it was seated in a spoon so not touching the bottom of the pot where the most heat was. Im not sure if the rubber is ok sitting on the bottom of the pot. I have also just poured boiling water into a cup with an atty and it works pretty well if it soaks until the water cools and you rinse it

 

[DawnBella]

I have an electric stove so i made sure it was seated in a spoon so not touching the bottom of the pot where the most heat was. Im not sure if the rubber is ok sitting on the bottom of the pot. I have also just poured boiling water into a cup with an atty and it works pretty well if it soaks until the water cools and you rinse it

As always .... U ROCK! Great idea! Have you noticed that the batts seem to charge a little too fast? I know the batt is dead, I place it in the PCC and 10 mins later the blue light goes out. That can't be right. It shroud be at least 25 mins. I even cleaned the connector and end of battery. Hmm? Grr. Better not be a broken unit.

 

[KrasH]

Figured out the rattle

 

[volume control]

As always .... U ROCK! Great idea! Have you noticed that the batts seem to charge a little too fast? I know the batt is dead, I place it in the PCC and 10 mins later the blue light goes out. That can't be right. It shroud be at least 25 mins. I even cleaned the connector and end of battery. Hmm? Grr. Better not be a broken unit.

I swear sometimes i take 5 puffs and it takes 20 minutes to charge and im just waiting to vape more, and other times its ready in 5 minutes. If it does kick off too early sometimes i probably wouldnt know because i tend to only take 20-30 vapes before charging, and ive never had an issue. If its really full and you pull it for a second it should only show the blue light for a minute or two, and guarantees a full charge. I dont think its great for the battery, but if you think no way, you could test it out and see if it runs a long time are reconnecting

 

[DawnBella]

k I'll keep an eye on it I guess. I will vape a batt down to blinky and then see how long it takes to charge.

 

[TennDave]

Mine always get sucked down to blinky and then I pull the one out of the PCC that's in there (if/when it's ready) and put the spent one in. I know the PCC and eRoll aren't meant to be used this way, but I can't help it!! I'm probably prolonging the life of my batteries this way but not the PCC.

 

[volume control]

k I'll keep an eye on it I guess. I will vape a batt down to blinky and then see how long it takes to charge.

From blink i think mine is like 30-40 minutes, i hit it the other night without realizing i had done that! Its nice to have a little kr808 handy. I prefer my cheaper devices, if i have problems i can junk them and buy others. If i had a provari and it broke id have to deal with warranty or a good chunk of cash on the spot. I consider a nice long lasting vape device for home at my desk, that reo mini looks pretty slick. I would never want to use something like that while driving or at work though, work because im stealthing

 

[TennDave]

Haha...funny you say that about the Reo Mini- before the eRoll that was definitely my stealth device...really it's so small that your hand will cover it up and there's no light to give it away! It also fits in the front pocket of any pair of jeans or trousers.

 

[volume control]

Haha...funny you say that about the Reo Mini- before the eRoll that was definitely my stealth device...really it's so small that your hand will cover it up and there's no light to give it away! It also fits in the front pocket of any pair of jeans or trousers.

I noticed they had the mini 2.0 in black in stock. Is its really much bigger? Im actually ok with thicker if its the same other than width, its the height im most concerned with


Is there anything else i should buy for it?

 

[unloaded]

Some LR 306 attys are nice on a bottom feeder. They are smaller and stealthier and have a warmer vape.

 

[volume control]

Some LR 306 attys are nice on a bottom feeder. They are smaller and stealthier and have a warmer vape.

Whatever you have below that grandpa pistol looks awful regal. If i broke in your house and you whipped out that mod, id probably just be your friend and decide not to rob you

 

[TennDave]

I noticed they had the mini 2.0 in black in stock. Is its really much bigger? Im actually ok with thicker if its the same other than width, its the height im most concerned with


Is there anything else i should buy for it?

Height and width is the same as the mini- it's the depth that is more.... but there's a 2.1 that's about to come out...it will be more rounded in the back and the juice well will be larger to accommodate all the rebuildable atty's that are out there so you might want to hold off for a week or two. Rob has the 2.1 at the anodizers now from what I understand.

The 2.0 and 2.1 for that matter will take the AW IMR 18490/18500 batteries. Otherwise the connection is a 510. I have a ERA Atomizer on my 2.0 w/ an adapter but with the new 2.1 you won't need one. The Chalice and the Pheonix A-7 bottom feeder rebuildable atomizers will also fit it without an adapter.