Joytech Evic Menu

[Krispers]

Hola Peeps,

I just got a evic as a gift and i must say this darn confusing. When I power on the menu does not match what I see in the manual or psuardo's review.

When I just get to menu without powering on yet, I get :

power on
Sleep
vapor set
configure
device
exit

When I select power on, I get menu:

sleep
vapor set
configure
device
power off
exit

Everywhere I look I see there should be a power set option from main screen. My version is 1.3, and device id is 304150684. I know there may be knock offs but no clue on how to tell. Any insight would be helpful.

 

[JellieBean]

You didnt get a knock off mine is exactly as yours in the menu...

 

[crxess]

Vapor Set is where you get to power options. VV, VW, etc.
Ring right left is where you adjust volts/watts up/down.

Pbusardo review unit had v1.1
I run v1.2
Your 1.3 is the latest release.

1.3 had nothing I needed so I did not upgrade. Maybe next release.

 

[Amethyst_Star]

Same here, Krispers. It upset me when I asked a question in the forums here and someone answered "Read the manual." Um...the manual shows a completely different menu than what I have.

 

[Krispers]

thanks for your replies, I hate being confused and must say first time in the vaping world I ever have been....makes me feel like a ol' foggey

 

[roffles18963]

I'm just gonna assume the manual was for firmware 1.0, when I got mine it came with 1.2 and looked NOTHING like what was in the manual. Which isn't really a big deal. I don't really plug my eVic in to use MVR, I use an external charger and cycle 4 different batteries through it.

You can change the display on the upper left side of the screen by HOLDING the ring to the left, it'll switch between clock, current puffs/puffs remaining, and wattage/ohms (if using VV mode) or voltage/ohms (if using watts). You can also freely switch between Volts and Watts (and any MVR watt profiles you exported from MVR to the eVic) by holding the ring to the right. The things you couldn't find on the eVic that were shown in the manual can be modified through both MVR and the eVic itself, just under different menus.

 

[Amethyst_Star]

I'm just gonna assume the manual was for firmware 1.0, when I got mine it came with 1.2 and looked NOTHING like what was in the manual. Which isn't really a big deal. I don't really plug my eVic in to use MVR, I use an external charger and cycle 4 different batteries through it.

You can change the display on the upper left side of the screen by HOLDING the ring to the left, it'll switch between clock, current puffs/puffs remaining, and wattage/ohms (if using VV mode) or voltage/ohms (if using watts). You can also freely switch between Volts and Watts (and any MVR watt profiles you exported from MVR to the eVic) by holding the ring to the right. The things you couldn't find on the eVic that were shown in the manual can be modified through both MVR and the eVic itself, just under different menus.

Thanks, Roffles! Very helpful! I appreciate it!

 

[Chelley]

That's the only thing I don't like. I know I suck on this all day. Now I know how long my drag is too . LOL. But I do like it.

 

[roffles18963]

Just go into your menu, and under "Vapor Set" turn "Stealth" on. Now that you know how long your drags are, you don't have to be reminded of it every puff. XD

 

[roffles18963]

Thanks, Roffles! Very helpful! I appreciate it!

Whoops on the double post, but no problem!