Just got my Reo, have some issues :(

[armyofskittles]

Thankyou everyone for helping me get this baby rocking and rolling! Especially Redeyedancer.

Need tips on drip tips that will look good with this

Sent from my HTC6500LVW using Tapatalk

 

[SLIPPY_EEL]

To get your reomizer facing the right way, instead of putting the o-ring where you have it now i put mine around the brass colour part around bottom of mizer plus it fills the gap

Congrat's

 

[nerak]

Shoot a PM to redeyedancer. Robert needs to know this.

To order a milled cup it was standard procedure to PM Robert and he would send you an invoice. It was not done through the site. So, that is why your Grand is NOT milled.

RM2 does look milled to me.

Let Robert know.

 

[armyofskittles]

Shoot a PM to redeyedancer. Robert needs to know this.

To order a milled cup it was standard procedure to PM Robert and he would send you an invoice. It was not done through the site. So, that is why your Grand is NOT milled.

RM2 does look milled to me.

Let Robert know.

Ah crap! I didn't do the pm thing.. now I'm stuck with a goofy lookin reo haha. I did talk to him on here about the invoice thing but I didn't know how to have him send the invoice and did not want to bug him about it further. It's my own fault, no big deal so did I get the right combo then? UN milled reo with milled rm2? Or what

Sent from my HTC6500LVW using Tapatalk

 

[nerak]

Ah crap! I didn't do the pm thing.. now I'm stuck with a goofy lookin reo haha. I did talk to him on here about the invoice thing but I didn't know how to have him send the invoice and did not want to bug him about it further. It's my own fault, no big deal so did I get the right combo then? UN milled reo with milled rm2? Or what

Sent from my HTC6500LVW using Tapatalk

The Grand is NOT milled. The drip well would be very shallow. The RM2 looks like it is milled, but I am not 100% sure about it.

What you wanted is a MILLED Grand and a not milled RM2.

 

[armyofskittles]

The Grand is NOT milled. The drip well would be very shallow. The RM2 looks like it is milled, but I am not 100% sure about it.

What you wanted is a MILLED Grand and a not milled RM2.

Oh well I'll just have to make sure I do my next one right what about the door issue? It doesn't slide smoothly at all

Sent from my HTC6500LVW using Tapatalk

 

[Hdivr]

Someone may have thought milled "cap" instead of milled "cup"..... I can see that happening.........

 

[armyofskittles]

Also my aw imr battery, the red sleeve plastic stuff is kinda peeling on one part at the tip from my old mod, exposing some shiny metal. Do you think that might cause a problem

Sent from my HTC6500LVW using Tapatalk

 

[nerak]

Oh well I'll just have to make sure I do my next one right what about the door issue? It doesn't slide smoothly at all

Sent from my HTC6500LVW using Tapatalk

The door should slide better with a little use.

I am still going to tell you to send Robert a PM! Don't worry about bothering him. He wants to know these things. PM HIM NOW!

 

[Krazirob]

id still contact him about the 510 connection being scarred......but congrats....now lets see some pics of that bad boy vaping!!!!!

 

[armyofskittles]

id still contact him about the 510 connection being scarred......but congrats....now lets see some pics of that bad boy vaping!!!!!

The rm2 is not making contact. I tested my hh357 and it worked, but rm2 is not firing wrapped a 1 ohm coil firing with my aw imr... No idea why it's not firing. It's only screwing 2 full turns into the 510. How many turns do your rm2s go in

Sent from my HTC6500LVW using Tapatalk

 

[armyofskittles]

The door should slide better with a little use.

I am still going to tell you to send Robert a PM! Don't worry about bothering him. He wants to know these things. PM HIM NOW!

I feel bad! I'll see if the issues sort themselves out or maybe I can fix them

Sent from my HTC6500LVW using Tapatalk

 

[Rmcgloth]

Also my aw imr battery, the red sleeve plastic stuff is kinda peeling on one part at the tip from my old mod, exposing some shiny metal. Do you think that might cause a problem

Sent from my HTC6500LVW using Tapatalk

I personally don't like to see anything shiny on a battery but the contacts. Depending on the location it may not cause a problem. The casing is negative, I believe, so body grounds shouldn't produce a short. That said, a little tape is cheap insurance.

 

[Krazirob]

mine goes about 5 or 6 full rotations........hope you get it all fixed with ROB the REO MASTER

 

[armyofskittles]

mine goes about 5 or 6 full rotations........hope you get it all fixed with ROB the REO MASTER

Hmmmmm! Still can't get it to fire

Sent from my HTC6500LVW using Tapatalk

 

[ltrainer]

have you rotated the firing button counterclockwise to unlock it?

 

[Funk Dracula]

To get your reomizer facing the right way, instead of putting the o-ring where you have it now i put mine around the brass colour part around bottom of mizer plus it fills the gap

Congrat's

I think your supposed to have the o-ring around the 510 air slots like he does (well his is half off in the pic.) As far as I unserstand it, you want it there for two reasons.

1.) It prevents juice from going outside the 510 connection at all and in into the catch-cup, and also helps create the conditions to better suck the juice down back into the bottle post-squonk.

2.) It still gives you a buffer to tighten down your RM2 in order get your air-hole and coil facing the desired position when screwed in.

I think people are putting an additional o-ring up over the milled part to yes, help cover any gaps appearing above the catch-cup visually, but I think around the 510 connection base is the way it supposed to work. With the 510 air slots still exposed, some juice will flood the catch-cup just like bottom airflow atty's or cartos do, less juice will find it's way to the RM2's deck.

-B

 

[armyofskittles]

I'm not having any luck lol

Sent from my HTC6500LVW using Tapatalk

 

[Krazirob]

have you rotated the firing button counterclockwise to unlock it?

yes in case you didn't know this already the button can lock......hope that is the issue so you don't have to send it back

 

[MamaTried]

did you try firing it without the o-ring just to rule that out?